Heavy crude oil sg0925 and nu10x10-4 m2s is pumped through

Assignment Help Mechanical Engineering
Reference no: EM13624262

Heavy crude oil (SG=0.925 and ν=1.0x10-4 m2/s) is pumped through a pipeline laid on flat ground. The line is made from steel pipe with 600 mm i.d. and has a wall thickenss of 12 mm. The allowable tensile stress in the pipe wall is limited to 275 MPa by corrosion considerations. It is important to keep the oil under pressure to ensure that gases remain in solution. The minimum recommended pressure is 500 kPa. The pipeline carries a flow of 400,000 barrels (a barrel is 42 gal) per day. Determine the maximum spacing between pumping stations. Compute the power added to the oil at each pumping station.

Reference no: EM13624262

Questions Cloud

Saturated water vapor at 350c is heated at a constant : saturated water vapor at 350c is heated at a constant pressure until its volume has doubled. determine the final
Data analysis problem for the data set below calculate the : data analysis problem for the data set below calculate the following mean or average variance standard deviation mode
Portable electric heaters are commonly used to heat small : portable electric heaters are commonly used to heat small rooms. explain the energy transformation involved during the
A ductile metal wire of uniform cross section is loaded in : a discuss the assumption that when a piece of metal is deformed at constant temperature its volume is unchanged.b a
Heavy crude oil sg0925 and nu10x10-4 m2s is pumped through : heavy crude oil sg0.925 and nu1.0x10-4 m2s is pumped through a pipeline laid on flat ground. the line is made from
Twenty percent of all telephones of a certain type are : twenty percent of all telephones of a certain type are submitted for service while under warranty. of these 60 can be
The induced electric field 13cm from the axis of a solenoid : the induced electric field 13cm from the axis of a solenoid with a 10cm radius is 48vm . find the rate of change of the
A local childrens boutique specializes in formal wear for : a local childrens boutique specializes in formal wear for young girls. it has recently hired a new seamstress. to
An air-standard dual cycle has a compression ratio of 9 at : an air-standard dual cycle has a compression ratio of 9. at the beginning of compression p1100kpa t1300k and v114l. the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd