Heat treatment in terms of surface carbon concentration

Assignment Help Mechanical Engineering
Reference no: EM13947966

The wear resistance of a steel shaft is to be improved by hardening its surface. This is to this case the initial carbon content of the steel is 0.15 wt%, and a carbon content of 0.75 wt% is to be established at a position 0.65 mm below the surface. Furthermore, the surface concentration is to be maintained constant, but may be varied between 1.2 and 1.4 wt% C. Specify an appropriate heat treatment in terms of surface carbon concentration and time, and for a temperature between 1000°C and 1200°C.

Reference no: EM13947966

Questions Cloud

Why a relation schema is an indexed set of sets : Why the states of a relation schema are the subsets of schemas product? Please give an example?
Describe your initial reaction to the video : Watch the following video about bystander apathy, and discuss the following prompts: https://www.youtube.com/watch?v=KIvGIwLcIuw, Describe your initial reaction to the video. What surprised you the most
How much safety stock should be ordered : At what point should a new order be placed if the candy store wishes to keep 95% level of service, assume normal demand and the lead time. How much safety stock should be ordered?
Determine the mean and the variance : Let four random variables X1, X2, X3, X4 have common mean m1=m2=m3=m4= 5 and common variance (sigma 1)^2= (sigma 2)^2= (sigma 3)^2= (sigma4)^2= 6 and common correlation coefficient p(sub ij)= .1, i does not equal j. Determine the mean and the vari..
Heat treatment in terms of surface carbon concentration : Specify an appropriate heat treatment in terms of surface carbon concentration and time, and for a temperature between 1000°C and 1200°C.
How to do forensic investigations on these crimes. : Find the most challenging crimes that could be based on P2P networks and write a report on how to do forensic investigations on these crimes.
Yellow cab contracted with the birmingham board of education : Yellow Cab contracted with the Birmingham Board of Education to transport physically handicapped students. The contract provided, "Yellow Cab will transport the physically handicapped students of the School System...and furnish all necessary vehicles..
Activation energy for the diffusion coefficient : Assume that the preexponential and activation energy for the diffusion coefficient are 1.5 x 10-4  m2/s and 125,000 J/mol, respectively.
Japan has a gap inflationary or recessionary gap : Japan has a gap inflationary or recessionary gap, and what is its magnitude?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A mass of 3 kilograms of steam at 2 mpa and 250degc are

a mass of 3 kilograms of steam at 2 mpa and 250degc are contained in a rigid tank. how much heat must be removed from

  What is the velocity in the 4-inch pipe

Water at 150C flows in 1½-inch Sch 40 steel pipe with a flow velocity of 2.86 m/s. The pipe expands to 4-inch Sch 40.

  Find the velocity and discharge in the pipe

A reservoir discharges into a 4-inch new cast iron pipe, as shown below. Find the velocity and discharge in the pipe. Consider friction, but neglect minor losses.

  A tank open to the atmosphere initially contains 2 lb of

a tank open to the atmosphere initially contains 2 lb of liquid water initially at 80degf and 0.4 lb of ice initially

  Distillery uses mechanical vapour re-compression

The wash still in a whisky distillery uses mechanical vapour re-compression as shown in the simplified diagram of the Figure shown below. The vapour from the still is at 80° C. Take a minimum temperature difference between the vapour leaving the stil..

  Two blocks a and b of mass 8 kg and 12 kg respectively hang

two blocks a and b of mass 8 kg and 12 kg respectively hang from a cable which passes over a pulley of negligible mass.

  Calculate the volume flow rate of the steam at the

steam enters the adiabatic condenser i.e.heat exchange of a steam power plant at 20 kpa 95 percent quality and with a

  Discuss johnson & johnson''s approach on providing an it

Needing a writing help with a 3-4 page paper on the Case Study 6-2 Johnson & Johnson's Enterprise Architecture, this is from Managing and Using Information Systems by Pearson & Saunders.

  What is the pressure difference over the manometer in newton

what is the pressure difference over the manometer in newtons per meter?

  Create a window in java

Create a window apllication in java

  A four foot diameter reel of wire pays out 250 feet of

a four foot diameter reel of wire pays out 250 feet of conductor wire in two minutes. what is the average angular

  The currently used material is brass but you have decided

you are asked to design a solid circular shaft of minimum cost that is 1.3 m long and has to twist less than 3 degrees

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd