Heat transfer coefficient between gas and each wire is 200

Assignment Help Mechanical Engineering
Reference no: EM13612820

A thermocouple is placed in an exhaust pipe in a diesel engine. Thermocouple is reading 500oC, while the exhaust pipe is at a temperature of 350oC. Thermocouple used to measure the temperature of a gas flow is constructed of two bare wires. Thermal conductivity of one wire is 19.2 W/m-k and the other is 29.8 W/m-k. Heat transfer coefficient between gas and each wire is 200 w/m2-k. Estimate the conduction error in the measurement of gas temperature. The wire is 5 cm long and 1.5 mm in diameter.

Reference no: EM13612820

Questions Cloud

Determine the ratio of the energy used by the blow-dryer in : a blow-dryer and a vacuum cleaner each operate with a voltage of 120 v. the current rating of the blow-dryer is 11 a
The exit temperature of hot air is 20degc assuming constant : an adiabatic heat exchanger is used to heat cold water at 15degc entering at a rate of 5 kgs by hot air at 90degc
An objects temperature increases and in so doing its : an objects temperature increases and in so doing its radiation power increases by a factor of 2.00. what is the ratio
Parrish inc decided on january 1 to discontinue its : parrish inc. decided on january 1 to discontinue its telescope manufacturing division. on july 1 the divisions assets
Heat transfer coefficient between gas and each wire is 200 : a thermocouple is placed in an exhaust pipe in a diesel engine. thermocouple is reading 500oc while the exhaust pipe is
The following information pertains to sampson company : the following information pertains to sampson company. assume that all balance sheet amounts represent both average and
Each year management accounting reports the results of a : each year management accounting reports the results of a salary survey of the members of the institute of management
It takes 25uj of work to move a 16nc charge from point a to : it takes 2.5uj of work to move a 16nc charge from point a to b. it takes -5.5 uj of work to move the charge from c to
Assuming a 5-year straight-line depreciation how will this : an overall risk profile of the company based on current economic and industry issues that it may be facing.ii. current

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd