Heat transfer between the compressor and its surroundings

Assignment Help Mechanical Engineering
Reference no: EM13610441

Refrigerant 134a enters a compressor operating at steady state as saturated vapor at -4 °C and exits at a pressure of 1.4 MPa. The isentropic compressor efficiency is 85%. Heat transfer between the compressor and its surroundings can be ignored. Kinetic and potential energy effects are also negligible. Determine (a) the exit temperature, in °C. (b) the work input, in kJ per kg of refrigerant flowing.

Reference no: EM13610441

Questions Cloud

Accounting for the change is void fraction does this : liquid chromatography lc flow can be model as a packed bed and is described by the ergun equation. lc systems are often
Suppose 13 of american adults believe that the highest : suppose 13 of american adults believe that the highest priority of america is to protect freedom of speech. we will
The distribution of the amount of money in savings accounts : the distribution of the amount of money in savings accounts for university of miami students has an average of 1100
Calculate the volume flow rate of water if the pressure at : water at 80f is flowing from a to b in a 3-in coated ductile iron pipe. point b is 20ft higher than a and the total
Heat transfer between the compressor and its surroundings : refrigerant 134a enters a compressor operating at steady state as saturated vapor at -4 degc and exits at a pressure of
If the ph level of the reservoir is ok the results at each : a water treatment plant needs to maintain the ph of the water in the reservoir at a certain level. to monitor this they
Calculate the isentropic efficiency of the turbine if the : an adiabatic turbine handles air as the operating fluid such that the air is expanded from 2 mpa and 327 degc to 200
Consider a steam turbine where steam enters with a : consider a steam turbine where steam enters with a pressure of 10 mpa and temperature 500 degc and expands
Suppose 60 of american adults believe martha stewart is : suppose 60 of american adults believe martha stewart is guilty of obstruction of justice and fraud related to insider

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Find the axial stress in individual component

The system shown below is deflected in compression by 6 = 0.014 in. For individual components 1, 2 & 3 find the axial stress in individual component

  A carnot engine operates between temperatures of 700 and

a carnot engine operates between temperatures of 700 and 369 k. to improve the efficiency of the engine it is decided

  Determine the tension developed in cord cd determine the

determine the tension developed in each cord required for equilibrium of the 21- kg lamp. determine the tension

  Couette flow velocity distribution

Couette Flow Velocity Distribution, Using the log law, determine the velocity distribution for Couette flow between parallel plates a distance h apart, with U = the velocity of the top plate.

  Meaning of the term mechatronics

Briefly describe the meaning of the term mechatronics both in terms of the 'systems approach' and the technology involved.

  Calculate the static thrust of the turbojet engine

Calculate the static thrust of the turbojet engine having mass flow 88lbm/sec the ratio of air and fuel mass flowing into the turbojet is 50:1 and it's exhaust plane the velocity is 1640 ft/sec and pressure is same as ambient pressure?

  Determine the pressure of the water

determine the pressure of the water after the partition has been remived and enough heat has been transferred so that the temperature of the water is 3(degrees)C.

  Define and design a hollow steel shaft to transmit

Hollow shaft transmitting power with shear limits. Design a hollow steel shaft to transmit 300 hp at 75 rpm without exceeding a shear tress of 8000 psi. Use 1.2:1 as the ratio of the outside diameter to the inside diameter.

  Define the final state inside the tank

Find the final state inside the tank, A tank contains 2kg of nitrogen at 10K with a quality of 50%.Through a volume flow meter and valve, 0.5kg is now removed while the temperature remains constant.

  As the hollow steel g 77 gpa shaft shown rotates at 180

as the hollow steel g 77 gpa shaft shown rotates at 180 rpm a stroboscopic measurement indicates that the angle of

  What delta p must be generated by the pump comment of the

a civil engineer is designing a pipe to transport 178 m3s of water a distance of 4.35 x 104 m. to save capital costs he

  Assuming ideal gas behavior for the air and neglecting

a rigid well-insulated tank with a volume of 3 fe contains air at p1 22 lbfin2 and t1 475 bullr. the air is stirred by

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd