Heat is transferred to the water until the volume quadruples

Assignment Help Civil Engineering
Reference no: EM13533369

A piston-cylinder device initially contains 1.4 kg saturated liquid water at 200 C. Now heat is transferred to the wateruntil the volume quadruples, and the cylinder contains saturatedvapor only. Determine:

a) the volume of the tank

b) the final temperature

c) the internal energy change of the water

Reference no: EM13533369

Questions Cloud

How long will it take him to reach the same velocity the : For the free-falling patachutist with linear drag, assume a firstjumper is 70 kg and has a drag coefficient of of 12 kg/s. If a second jumper has a dragcoefficient of 15 kg/s and a mass of 75 kg, how long will it take him to reach the same velocity t..
Provide your code for completing curve fitting : Plot ω vs t, marked by red stars. Label the x-axis, t,and the y-axis, ω. Give the plot a suitable title. Add a legend to the plot describingthe relationship between ω and t. Change the y-axis scale to show the plotfrom estimate ω is -100 to 1100.
Balance the following acid base neutralization reaction : Balance the following acid base neutralization reaction. Identifythe acid and the number of equivalents per mole. Identify the baseand the number of equivalents per mole.
Determine the pressure rise in the tire when the air : The pressure in a tire depends on the temperature of the air in atire. When the air temp is 25 C, the pressure gage reads 210KPa. If the volume of the tire is 0.025 m3
Heat is transferred to the water until the volume quadruples : A piston-cylinder device initially contains 1.4 kg saturatedliquid water at 200 C. Now heat is transferred to the wateruntil the volume quadruples, and the cylinder contains saturatedvapor only
Due to the nature of the waste water : Due to the nature of the waste water, you want to target the high end of this range.Find the proper diameter pipe to the nearest 2" to achieve thisdesign objective.
Determine the maximum depth of water possible without : A 1-m diameter cylindrical mass, M, is connected to a 2-m widerectangular gate. The gate is to open when the water level,h, drops below 2.5 m. Determine the required value forM. Negate friction at the gate hinge and the pulley.
Determine the base of the following arithmetic operation : A distance of 72.55ft. is recorded. A steel tape is supported atthe ends with a tension of 15 lb. and weighting 0.016lb/ft2 . Find the distance corrected for sag.
Solve the problem using the darcy weisbach : An effluent holding pond to be used as part of a spray irrigations system is being built.  The holding pond is located 2.5 miles awary for the 10 mgd WWTP which will supply the effluent

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculate what is the pressure at the siphon crown

The siphon crown is 1.2m above the water surface elevation of the reservoir and a length 10m away from the siphon entrance. If the siphon diameter is 30 cm, if the friction factor is .02, and the headless coefficient are .2 (inlet) and 1 (exit),

  Determine what is the rate of flow into the reservoir

Runoff from a storm flows into a reservoir with a surface area of 20.0 ha at a constant rate. The reservoir level is observed to rise at 1 mm per minute when water is being released through the dam at a rate of 10 m3 per second.

  Calculate bending stress distribution which present at base

Assume the beam is 2" x 10" in cross section. Calculate the bending stress distribution that is present at the base of the cantilever and at every 2.5 ft increment toward the free end of the beam

  Bernoulli equation-measure the flow rate through the meter

The meter inlet and throat are connected by the two legs of a mercury manometer. Use the Bernoulli equation to describe how this manometer can be used to measure the flow rate through the meter.

  Calculate the area of reinforcement required

A short Reinforced Concrete column is 300mm x 400mm. It is required to carry an ultimate load of 1500kN and an ultimate major axis bending moment of 300kNm. Calculate the area of reinforcement required.

  Determine the flow regime sub or super- critical downstream

determine the rate of discharge through the gate; b) determine the critical depth , yc at the minimum energy, Es,min; c) determine the critical depth, yc at the current flow; d) determine the alternate depth; e) determine the flow regime (sub- or ..

  Determine the void ratio to be perfectly dry soil

A soil sample with specific gravity of solids 2.70 has a mass specific gravity of 1.84 Assuming the soil to be perfectly dry,Determine the void ratio.

  Find what is the pressure on the soil if theta is 45 degrees

A pipe is to be installed under the ground on a bed of aggregate 6 in. thick. The entire weight on the aggregate from pipe and soil above the pipe is 1800 lbs. per linear foot of pipe. What is the pressure on the soil if theta is 45 degrees

  A segment of urban four-lane two lanes in each direction

nbspa segment of urban four-lane two lanes in each direction has a 3 upgrade that is 1500 ft long followed by a 1000-ft

  Determine the volume flow rate of water

Water with a static pressure of 1.96kN/M 2 flows through an 800 mm diameter pipe. A pitot tube pressure gage in this pipe reads a pressure of 5.88 kN/M 2 . How do you determine the volume flow rate (Q) of the water? (Q = 1.40 M^3/sec, V=2.79 M/se..

  Determine longitudinal and hoop stresses in the copper pipe

Typical water supply at a faucet in any building is conveyed in copper pipe that is ½" in inside diameter, with a wall thickness of 0.040". If the water pressure is 50 psi and the valve is closed (meaning that water is not flowing)

  What is coefficient of static friction on verge of sliding

A chair weighing 150 rests on a level floor that is not frictionless. A man pushes on the chair with a force = 43.0 that is directed at an angle of 34.0 with the horizontal. Assume that the chair is stationary but is on the verge of sliding.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd