Heat in the amount of 100 kj is transferred directly from a

Assignment Help Mechanical Engineering
Reference no: EM13632080

1. Air is compressed by a 30 kW compressor from P1 to P2. The air temperature is maintained constant at 25 oC during this process as a result of heat transfer to the surroundings at 17 oC. Determine the entropy change of the air.

2. Heat in the amount of 100 kJ is transferred directly from a hot reservoir at 1200 K to a cold reservoir at 600 K. Calculate the entropy change of the two reservoirs and determine if the increase of entropy principle is satisfied.

3. Is a process that is internally reversible and adiabatic necessarily isentropic? Explain using an equation.

4. A well- insulated rigid tank contains 5 kg of a saturated liquid-vapor mixture of water at 150 kPa. Initially three-quarters of the mass is in the liquid phase. An electric resistance heater placed in the tank is now turned on and kept on until all the liquid in the tank is vaporized. Determine the entropy change of the steam during this process.

5. Steam enters a turbine at a pressure of P1 = 6 MPa and a temperature of T1 = 400 oC and leaves at a pressure of P2 = 100 kPa. Find the change in Specific Enthalpy of the steam if the expansion process is isentropic.

6. A piston-cylinder contains 1.2 kg of saturated water vapor at an initial temperature of T1 = 200 oC. Heat is transferred to the steam, so that the steam expands reversibly and isothermally to a final pressure of P2 = 800 kPa. Determine the heat transferred and the work done during this process.

Reference no: EM13632080

Questions Cloud

We want to achieve a concentration of 05wt of carbon at a : we want to achieve a concentration of 0.5wt of carbon at a depth of 0.2 mm below the surface of the slab of a metal.
Water at 10 degrees c flows throug a smooth 60-mm-diameter : water at 10 degrees c flows throug a smooth 60-mm-diameter pipe with an average velocity of 8ms. would a layer of rust
Consider a system operating a power cycle between thermal : consider a system operating a power cycle between thermal reservoirs at temperatures th and tc where thgttc. using 1st
A diesel engine has a state before compression of 95 kpa : a diesel engine has a state before compression of 95 kpa 290 k a peak pressure of 6000 kpa and a maximum temperature of
Heat in the amount of 100 kj is transferred directly from a : 1. air is compressed by a 30 kw compressor from p1 to p2. the air temperature is maintained constant at 25 oc
Liquid water enters a pump at 15degc 100 kpa and exits at : liquid water enters a pump at 15degc 100 kpa and exits at a pressure of 5 mpa. if the isentropic efficiency of the pump
Determine the evaporator temperature at which a : the overall volume compression ratio of a reversed carnot cycle working with air as a refrigerant is 10. the
Combustion products with the molar anaylisis of 10 co2 20 : combustion products with the molar anaylisis of 10 co2 20 h2o 70 n2 enter an engines exhaust pipe at 1000f 1atm and are
If the static and kinetic friction coefficients between the : a spool of mass m214 kg inner and outer radii p1.84 m and r 2.23 m respectively and the radius of gyration kg 2m is

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd