Heat engine operating on the carnot cycle

Assignment Help Mechanical Engineering
Reference no: EM13718125

1. A heat engine operating on the Carnot cycle has an efficiency of 65%. The waste heat from the cycle is rejected to the atmosphere at 20 deg. C. at a rate of 250 kW. What is the temperature of the heat source driving the engine in deg. C?

2. For the heat engine in the above problem, what is the power output in kW?

Reference no: EM13718125

Questions Cloud

What is the meaning of leadership : What is the meaning of leadership - vitality of leadership in the field of education
Determine the shear modulus of the eraser material : A cylindrical eraser of negligible mass is dragged across a paper at a constant velocity to the right by its pencil. Determine the shear modulus of the eraser material
Consider three lans interconnected by two routers : Consider three LANs interconnected by two routers as shown in Figure below. Assign IP addresses to all of the interfaces. For Subnet 1 use addresses of the form 192.168.1.xxx; for Subnet 2 use addresses of the form 192.168.2.xxx; and for Subnet..
Current network design : Imagine that you are the administrator for a small accounting company, which currently employees 200 people. The CEO announces a merger that would double the number employees to 400. Your current network design is as follows:   Current network ..
Heat engine operating on the carnot cycle : A heat engine operating on the Carnot cycle has an efficiency of 65%. The waste heat from the cycle is rejected to the atmosphere at 20 deg. C. at a rate of 250 kW. What is the temperature of the heat source driving the engine in deg. C? For the heat..
Magnitude of the support reaction on the left end of beam : A 20ft long beam has a support reaction at each end and a 12ft long uniformly distributed load of 20lb/ft starting on the left edge. The uniformly distributed load is modeled as a normal concentrated load of how many pounds?
Closed piston-cylinder arrangement : One half of a mole of air is taken through the following processes in a closed piston-cylinder arrangement. From the initial state (V1 = 10 L, p1 = 1 atm) the gas is expanded at constant pressure to a volume of 20 L. It is then heated at constant vol..
Find that she cannot move either leg. advise aurelie : Explain how the common law and statutory rules of interpretation could be applied to the situations - Winnie is caught by a security guard as she is licking white aspirin powder.
Certain power station produces an electrical output : A certain power station produces an electrical output of 700 MW, operating at 42% efficiency. This plant uses a closed-circuit "dry" cooling system in which heat is expelled by cycling the cooling water through pipes which are in direct contact with ..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Round up to the nearsest millimeter when reporting

An engineer determines that a 40 cm long rod of 1020 grade steel will be subjected to a tension of 20 kN.

  Determine the column height in meters and feet if mercury

mercury is often used in barometers. this is because tje vapor pressure of mercury is low enough to be ignored and

  Determine the maximum exit velocity for this nozzle

Air enters an adiabatic nozzle at 5.18 MPa and 400K with a velocity of 20 m/s. The air exits at 2.00MPa. Determine the maximum exit velocity for this nozzle.

  What is velocity and acceleration of ball at tube

canon at an angle 30 degree tube is rotating at an axes with anguar velocities w1 and w2 2 and 5 rad/s and tube blows a ball at b with constant rate 7 m/s . what is velocity and acceleration of ball at tube end ball is at distance of 3m from tube ..

  Employing the ideal gas model with constant specific heat

air undergoes a polytropic expansion process in a piston-cylinder assembly from 75 psia and 300 f to 15 psia. employing

  Determine the angular acceleration using force-acceleration

part a.the slender bar ab rests on a smooth surface at b and is attached to a collar a that slides freely on the smooth

  A system consisting of 3 lb of water vapor in a

a system consisting of 3 lb of water vapor in a piston-cylinder assembly initially at 350 degrees f and a volume of

  A rigid container having a volume of 12 m3 contains 10

a rigid container having a volume of 1.2 m3 contains 10 percent by volume of liquid water at 100 kpa. the remaining

  Paint plant air house

Electricity might be used to run the fan to draw air through the system, and also to run a chiller - What is a typical COP for a commercial chiller?

  The particle a is mounted on a light rod pivoted at o and

the particle a is mounted on a light rod pivoted at o and therefore is constrained to move in a circular arc of radius

  Compare the results of part a with those of a reversible

a power cycle operate between hot and cold reservoirs at 600k and 300k receptively. at steady state the cycle develops

  Throttled from saturated liquid state

Refrigerant-134a is throttled from saturated liquid state at 7 bar to a pressure of 1.4 bar. Determine the temperature drop during this process and the final specific volume.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd