Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Heat and Mass Transfer Engineering Project
Problem
Dust and fumes are being extracted from various locations of a metal workshop by a multiple-hood system schematically shown in Figure 1. Commonly, such systems consist of a main duct run with individual branches joining the main at several locations. A centrifugal fan is being used to provide the air flow sufficient to meet the health and hygiene requirements applied to the quality of ambient air in the workshop. The face velocity of the air in the hoods was found to be ...... m/s and the cross- section area of each hood (measured at the inlet plane) is ...... m2. The aerodynamic resistance of the hood is approximately ...... Pa. The contaminated air carrier is purified by a plate scrubber before release to the atmosphere. Scrubber is equipped by four sieve plates and total aerodynamic resistance of the device is ...... Pa. The irrigation rate required for efficient operation of the scrubber is ...... m3/h
You are asked to design pipelines suitable for the application and choose the fan to meet the airflow and pressure requirements. The final document will have:
1. Scaled diagram of the system with all dimensions on it (top and side views).2. All calculations required to determine optimum sizes of the air and scrubber irrigation pipes.3. Recommendations on the type of the fan suitable for the application.
In addition, a common room at the facility is used by personnel for food consumption and resting (Fig. 2). An air conditioning system is required for providing comfortable temperature of 23°C. You are asked to select the room dimensions (X= m, Y= m and Z= m) and design a split air conditioning system suitable to meet the requirements for Brisbane climatic conditions. The room can accommodate up to staff members. The following kitchen appliances are used in the room: (for example) coffee machine, 2 microwaves, cooktop and dishwasher
Attachment:- Design Problem.rar
a differential nitrogen pressure exists across a 3 mm thick steel furnace wall. after some time steady-state diffusion
a material element experiences 50 mpa compression in the x-direction 10 mpa tension in the y-direction and a negative
Plot the total mass in the tank, in kg, and the amount of heat transfer, in kJ, versus the final quality x ranging from 0.2 to 1.0
the inner and outer surfaces of a 0.3 m thick 400?cm x 700?cm north wall of an electrically heated home are maintained
SAN JOSESTATEUNIVERSITY-USA-The two dimensional front views of three objects are shown below. Use SolidWorks to model the three objects.
A W250×115 structural steel column is to carry an axial load of 1300 kN. The ends are pinned. Determine whether or not the column is adequate if the length is 6 m.- the length is 9 m.
If the Earth were suddenly stopped in its orbit, how long would it take for it to collide with the Sun? [Regard the Sun as a fixed point mass. You may make use of the formula for the period of the Earth's orbit.]
A steel cube 100 mm on a side weighs 80 N. We want to hold the cube in equilibrium under water by attaching a light foam buoy to it. If the foam weighs 470 N/m3, what is the minimum required volume of the buoy?
In order to increase production rate, a reactor setpoint was increased from 160 psig to 190 psig. The reactor pressure transmitter was recalibrated from 0- 200 psig to 0- 300 psig. What is the percent span for the old and new setpoints?
Cable TV companies allow a single connection per subscriber. How can they tell if the subscriber connects more than one TV set to the same line? Design a test to detect multiple connections.
a piston cylinder arrangement has two compartments a and b filled with water as shown in the figurebelow. compartment a
A stepping motor has 200 step angles. Its output shaft is directly coupled to leadscrew with pitch = 0.250 in. A worktable is driven by the leadscrew.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd