He exit quality is 90 at 1 bar and average flow speed of 50

Assignment Help Mechanical Engineering
Reference no: EM13627987

Consider a steam turbine operating at steady-state. There is one inlet and one outlet, tand adiabatic conditions may be assumed. Apply the first law for a control-volume to determine the power output. Inlet conditions are 125 bars, 420 degrees C, and average flow speed of 100 m/s. The inlet is area 100 cm^2 at a height of 2 m above the datum. The exit quality is 90% at 1 bar and average flow speed of 50 m/s, at a height of 50 cm above the datum. Determine the following:

a) the mass flow rate in kg/s

b) the change in specific enthalpy in kJ/kg

c) the change in kinetic energy per unit mass in kJ/kg

d) the change in potential energy per unit mass in kJ/kg

e) the shaft work in kJ/kg

f) the exit area in cm^2

g) the power output of the turbine in kW

h) the percent power output due to changes in enthalpy

i) the percent power output due to changes in kinetic energy

j) the percent power output due to changes in potential energy

Reference no: EM13627987

Questions Cloud

To obtain maximum magnification and an image that can be : a lens that has a focal length of 3.99 cm is used as a magnifying glass.a to obtain maximum magnification and an image
At what frequency should this cord be vibrated such that a : a 2.5 meter long elastic cord is fixed at both ends.a if the cord is vibrated at a frequency of 35-hz a n3 standing
He exit quality is 90 at 1 bar and average flow speed of 50 : consider a steam turbine operating at steady-state. there is one inlet and one outlet tand adiabatic conditions may be
How far from the slide should the lens of the projector be : the projection lens in a certain slide projector is a single thin lens. a slide 24.5 mm high is to be projected so that
He exit quality is 90 at 1 bar and average flow speed of 50 : consider a steam turbine operating at steady-state. there is one inlet and one outlet tand adiabatic conditions may be
Find the approximate probabilities that s is less than or : suppose that a basketball player can score on a particular shot with probality .3. use the central limit theorem to
A piston mp 5 kg is fitted in a cylinder a 15 cm2 that : a piston mp 5 kg is fitted in a cylinder a 15 cm2 that contains a gas. the setup is in a centrifuge that creates an
Light of wavelength 550nm is incident normally on a : light of wavelength 550nm is incident normally on a diffraction grating. the seventh order maximum of the diffraction
What is the resulting steady flow now how does the vector : motion with wind stress rotation and friction in the following you may use these values if neededmiddot density

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd