Greatest reverse voltage that will appear across the diode

Assignment Help Electrical Engineering
Reference no: EM13297762

1- In each of the ideal-diode circuits shown in the figure below, v1 is a 1-KHz, 10-V peak sin wave. Sketch the waveform resulting at v0. What are the positive and negative peak values?

1519_What are the positive and negative peak values.png

2- Assuming that the diodes in the circuits below are ideal, utilize Thévenin theorem to simplify the circuits and thus find the values for the labeled currents and voltages.

155_What are the positive and negative peak values1.png

3- (D) For the rectifier circuits shown below, let the input sin wave have 120-V rms value and assume the diode to be ideal. Select a suitable value of R so that the peak diode current doesn't exceed 50 mA. What is the greatest reverse voltage that will appear across the diode?

1389_What are the positive and negative peak values2.png

4- In the diode circuit shown below, R1 = 2kΩ, R2 = 1kΩ, V1 = 12V and V2 = 15V. Determine the diode currents I1 and I2. Assume that cut-in voltage for both diodes is VΥ = 0.7V.

111_What are the positive and negative peak values3.png

5- The diode circuit shown in the figure below has R = 30kΩ and VDD = 10V. Determine the current io and voltage vo if

a. vs = 5V
b. vs = 12V

You may assume that cut-in voltage for all diodes is VΥ = 0.7V.

1750_What are the positive and negative peak values4.png

6- Find the voltage vo and current io in the diode circuit shown below if R1 = 5kΩ, R2 =10kΩ, v1 = 5V and v2 = 10V. Assume that cut-in voltage for all diodes is VΥ = 0.7V.

406_What are the positive and negative peak values5.png

Reference no: EM13297762

Questions Cloud

What is the distance in meters : Consider a point charge with a charge Q, located at the origin, in an empty space. Let the electric potential be zero at infinity. What is the distance r, in meters
Write a loop that will estimate the value of the moody f : Use input values of epsilon (B1), pipe radius (B2), and Reynolds number (B3) to estimate "f" and place these in the same cells . Display the final answer in a message box and round to five figures. Use a short cut key of Ctrl+g
Analyzes the organizations basic legal-social environments : Analyzes the organization’s basic legal, social, and economic environments. Analyzes the organization’s managerial, operational, and financial issues including:
What cost allocation should the land receive : A parcel of corporate land was recently dedicated as the new plant site. What cost allocation should the land receive.
Greatest reverse voltage that will appear across the diode : Determine the diode currents I1 and I2. Assume that cut-in voltage for both diodes is VΥ = 0.7V and what is the greatest reverse voltage that will appear across the diode?
How to determine the npv and the profitability index : A four year financial project has net cash flows of $20,000; $25,000; $30,000; and $50,000 in the next four years. It will cost $75,000 to implement the project. If required rate of return is 20%, conduct a discounted cashflow calculation
Find expression for the interest paid in 24th installment : The amount of interest paid in the 3rd installment is a; the amount of interest paid in the 17th installment is b. Find the expression for the interest paid in the 24th installment.
What are the different ways the financial system have dealt : What are the different ways the financial system have dealt with the residentail mortagages being difficult for the financial system to handle?
Why is the residential mortgage a difficult loan : why is the residential mortgage a difficult loan for the financial system to handle?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What is the expression for fourier transform of dtmf signal

Sketch the amplitude spectrum of a DTMF signal with finite duration. You should make this sketch by hand, using the Fourier transform expression obtained in part 1). What happens to the DTMF spectrum when T is "too small"

  Calculate the capacitive reactive power of capacitor bank

A power factor correction capacitor bank, with negligible resistance, draws a current of 625 amperes whenconnected to its 480 VAC, 60 Hz source. Calculate the capacitive reactive power of the capacitor bank.

  Determine the dynamic behavior of the tank concentrations

Determine the dynamic behavior of the tank concentrations (CA0 and CA) in response to a step change in inlet concentration by 0.925 mole/m3. Estimate the time it takes until 63% of the change in outlet concentration, CA has occurred.

  How much energy is imparted to an electron

For a given lithium ion battery, it can supply 0.85 ampere-hours, or 850 (mAh) with a constant output voltage of 3.6 (V). How much energy is stored in this lithium ion battery. How much energy is imparted to an electron that flows

  What is probability that power supply selected at random

If the lower and upper specification for voltage are 4.95V and 5.05 V, respectively what is the probability that a power supply selected at random will conform to the specification on voltage

  What is the system nyquist sample rate

What is the system's Nyquist sample rate if ω0 = 1000/(2π) rad/sec.?

  Find maximum current that a fully-charged d-cell can supply

Find the maximum current that a fully-charged D-cell can supply-if only briefly-such that itsterminal voltage is at least 1.0V. Assume an emf of 1.5V andan internal resistance of 0.12 ohm.

  Determine wmax for a capacitor which occupies a volume x

Suppose the volume X occupied by a capacitor is A*d where A is the total area of the dielectric layers and d is the thickness of each dielectric layer (this assumes that the metal plates are infinitely thin).

  Draw the state diagram for a fsm that detects the sequence

a) Draw the state diagram for a FSM that detects the sequence r = 0101 (without overlaps). b) The FSM in part a can beimplemented with 3 FFs. Assume the state assignments are A = 000, B= 001, C = 100, D = 110

  The design must show all stages used in its development

The design must show all stages used in its development and must be implemented and tested in PSpice and suitable timing waveforms produced.

  Define what is the channel capacity for a channel

What is the channel capacity for a channel with a 300 Hz bandwidth and as S/N = 3? 2nd problem: Given a channel with a 50 kHz bandwidth and a S/N = 127, determine:

  What is the rms magnitude of the voltage at the source end

A group of small appliances on a 60Hz system requires 20 kVA at 0.85 pf lagging when operated at 125V (rms). The impedance of the feeder supplying the appliances is 0.01 + j0.08 Ohms. The voltage at the load end of the feeder is 125V (rms).

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd