Generate an expression for the stream function along the

Assignment Help Mechanical Engineering
Reference no: EM13628635

Consider a fully developed Couette flow, i.e. flow between two infinite parallel plates separated by distance h with the top plate moving with velocity V and the bottom stationary, as illustrated in figure Q3a below. The flow is steady, incompressible, and two dimensional in the x-y plane.
ryˆˆ The velocity field is given by V =V h i + 0j.

i. Is this flow rotational or irrotational? If it is rotational calculate the vorticity component in the z-direction. Do fluid particles rotate clockwise or counter clockwise?

ii. Generate an expression for the stream function along the vertical dashed line. For convenience let ?=0 along the bottom wall of the
channel. What is the value of ? along the top wall?

iii. Calculate the volume flow rate per unit width from first principles (integration of the velocity profile) and compare your result to that
obtained directly from the stream function.

iv. What is the shape of the streamlines for this flow? Do you expect them to be equally spaced? Explain.

Reference no: EM13628635

Questions Cloud

One day george was experimenting with friction and : one day george was experimenting with friction and attempting to pull al across the surface of a floor. george applies
A 3 cubic meter tank contains propane at 05 mpa and 3degc : a 3 cubic meter tank contains propane at 0.5 mpa and 3degc. gas leaks out of the tank. at the time of detection of leak
Find the expressions for the velocities vupper and vlower : the wye joint in the figure splits the pipe flow into three equal parts q3 q3 and q3 having the same uniform velocity
The generator of a series rcl circuit is set to a very low : 1 a resistor and a capacitor are connected in series to an ac generator which is initially set to 120 v rms and a
Generate an expression for the stream function along the : consider a fully developed couette flow i.e. flow between two infinite parallel plates separated by distance h with the
A massive ring radius a and mass m lies on the xy plane : a massive ring radius a and mass m lies on the xy plane. calculate the force f on a test mass m at position z on
It just moves on a keplerian orbit under the influence of : flight to mars. to send a satellite from earth to mars a rocket must accelerate the satellite until it is in the
If these components have weights wa 45 000 1b wb 8000 1b : due to an unequal distribution of fuel in the wing tanks the centers of gravity for the airplane fuselage a and wings b
A massive ring radius a and mass m lies on the xy plane : a massive ring radius a and mass m lies on the xy plane. calculate the force f on a test mass m at position z on

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd