Generalized mass and energy conservation equations

Assignment Help Mechanical Engineering
Reference no: EM13711860

Steam at 2.5 MPa and 400 C enters an adiabatic steam turbine with a low velocity and leaves with a velocity of 180 m/s at a pressure of 15 kPa and a quality of 90 percent. Assume steady state for the current problem state. Neglect potential energy.

A) Write down the generalized mass and energy conservation equations and simplify them for current problem,

B) Calculate the work in kJ/kg done per unit mass of the steam flowing through the turbine.

C) If the steady state power output of turbine is 5 MW, calculate the mass flow rate in kg/s of the steam.

Reference no: EM13711860

Questions Cloud

What is the smallest radius of an unbanked track : What is the smallest radius of an unbanked (flat) track around which a bicyclist can travel if her speed is 30 km/h and the coefficient of static friction between tires and track is 0.21
Solar water heater operating at steady state heats water : A solar water heater operating at steady state heats water from 90F to 120F. The panel is 3600 Btu/hr. Determine 1) the mass flow rate of the water in lb/min and 2) the volume of 120F water after 1 hour in gallons.
Explain what parole and probation departments do : Explain what parole and probation departments do -  Research agencies and organizations and identify at least three examples of codes of ethics for probation and parole agencies.
Find its height of the tower on a hot day : An iron tower in is 358 meters tall on a cold day (T = -9.4 degrees Celsius). What is its height of the tower on a hot day
Generalized mass and energy conservation equations : Steam at 2.5 MPa and 400 C enters an adiabatic steam turbine with a low velocity and leaves with a velocity of 180 m/s at a pressure of 15 kPa and a quality of 90 percent. Assume steady state for the current problem state. Neglect potential energy.
What speed do you need to give a package : You are working for a shipping company. Your job is to stand at the bottom of a 5.5m -long ramp that is inclined at 39 degrees above the horizontal. What speed do you need to give a package
What is the mass of the copper block : A copper block is removed from a 300 degree Celsius oven and dropped into 1.00 liter of water at 20.0° C. What is the mass of the copper block
Determine the temperature of the environment : Scientists in a laboratory produce a sound wave in a simulated environment (air) with a velocity of 405 m/s. What is the temperature (in Kelvin) of the environment
What is the mass flow rate of the refrigerant in the cycle : A heat pump uses r134a as the refrigerant to keep a heated space at 20°c by pumping from a geothermal water source. Water from the geothermal source enters the evaporator (a heat exchanger) at 50°c and leaves at 40°c at a rate of 0.08 kg/s. The re..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd