Gasoline is being discharged from a pipe at point 2 at

Assignment Help Mechanical Engineering
Reference no: EM13625921

Gasoline is being discharged from a pipe at point 2 at elevation 66.66 m. Pint 1, located 965.5 m along the pipe from point 2, is at elevation 82.65 m, and the pressure there is 2.50 kPa. If the pipe roughness is 0.500 mm, what pipe diameter is needed to discharge gasoline ( ?= 7.05 kN/m3, µ = 2.92x10-4Ns/m2, ? = 719 kg/m3) at a rate of 0.10 m3/s? Solve this problem using two different approaches.

1) Use Moody chart and manual iteration (Answer: Q = 0.1394 ft3/s),

2) Use Colebrook equation and any kind of software tool such as Mathcad, excel or a programmable calculator.

Reference no: EM13625921

Questions Cloud

If the initial temperature of the pin is 800 degrees c : a molybendenum metal pin is 25 mm long and 2mm in diameter. the air surrounding the pin is 200 degrees c the walls of
Police response time to an emergency call is the difference : police response time to an emergency call is the difference between the times the call is first received by the
An inverted cone is placed in a water tank if the weight : an inverted cone is placed in a water tank. if the weight of the cone is 16.5 n what is the tensile force in the cord
You have a ball on a wire that is twirled in a circular : you have a ball on a wire that is twirled in a circular orbit with a radius of 3.3 m and the centripetal force acting
Gasoline is being discharged from a pipe at point 2 at : gasoline is being discharged from a pipe at point 2 at elevation 66.66 m. pint 1 located 965.5 m along the pipe from
The beam is 460 m long and has a mass of 260 kg excluding : a gymnast with mass 47.0 kg stands on the end of a uniform balance beam as shown in the figure. the beam is 4.60 m long
Explain using either time-dilation or length contraction : can a person in principle travel from earth to the galactic center which is about 2.30times104 lightyears distant in a
Oil with a kinematic viscosity of 00035ft3s flows through : oil with a kinematic viscosity of 0.0035ft3s flows through a 4-in-diameter pipe with a velocity of 15fts. what will be
You are out on your friends boat in mission bay soaking up : part 1you are out on your friends boat in mission bay soaking up rays and fishing for tuna. you have a big fat worm on

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Consider a gas turbine with turbine staging and reheating

consider a gas turbine with turbine staging and reheating. it operates under the following conditions.inlet air at 285

  Determine the outlet temperature of the hot fluid

Determine the outlet temperature of the hot fluid.

  Compute the percentage ionic character of interatomic bond

Compute the percentage ionic character of the interatomic bond for each of the following compounds: MgO, GaP, CsF, CdS, and FeO

  The system is returned to its initial state in a

1 kg of water executes a cycle in a piston cylinder assembly starting out at high t 300 deg c and high p 15 mpa. the

  Determine the rate of heat loss from the steam pipe

Taking the temperature of the surrounding surfaces to be 20°C also, determine the rate of heat loss from the steam pipe.

  The radial loads of both gears are in the same plane and

a shaft is to be designed to support the spur pinion and helical gear shown in the figure on two bearings spaced 700 mm

  Compute the moment of inertia of the system about an axis

small blocks each with mass m are clamped at the ends and at the center of a rod of length l and negligible mass.a

  Find the heat flux through the wall in si units find the

the inside surface of an 8-in-thick common brick wall is maintained at 100 f. thermal conductivity of th brick is 1.0

  There are 18 turns in the primary coil and 20 turns in the

a transformer consisting of two coils wrapped around an iron core is connected to a generator and a resistor as shown

  The temperature on the inner face is 25 degrees celcius and

a brick wall 3 m high 7.5 m wide and 200 mm thick has a thermal conductivity of 0.7 wmcelcius. the temperature on the

  How many positive impulses will be counted per second

A magnetic pickup is used to detect the shaft speed of a turbocharger. A standard hexagonal nut is used to excite the pickup. If the shaft is turning at 50,000 rpm, how many positive impulses will be counted per second?

  At the diffuser exit the temperature is 430 k determine the

air enters an insulated diffuser at 260 k and 60 kpa with a velocity of 633.9 ms. at the diffuser exit the temperature

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd