Gas behaviour and no change in kinetic or potential energy

Assignment Help Mechanical Engineering
Reference no: EM13711474

A closed, rigid tank fitted with a paddle wheel contains 0.1kgof air, initially at 300 K, 0.1MPa. The paddle wheel stirs the air for 20 minutes, with the power input varying with time according to W = -10t, where W is in watts and t is time, in minutes. The final temperature of the air is 1060K. Assuming ideal gas behaviour and no change in kinetic or potential energy, determine for the air

a) the final pressure, in MPa

b) the work, in kJ

c) the heat transfer, in kJ

Reference no: EM13711474

Questions Cloud

What is the resulting strain of the wire when it is used : Company wants to use a 100 m long steel cable to pull an airplane glider. If the glider has a mass of 1000 kg, and assuming the load is given by F=mg = 9800 N, and if the Young’s modulus of steel is 200 GPa (200,000,000,000 Pa), and Poisson’s ratio i..
Determine the stress and slenderness ratio : A 10 inch long cantilevered beam has a 1” by 1” square cross section. The load at the end of the beam cycles from 0 lbs to 300 lbs. determine the stress. Determine the slenderness ratio and column constant of a 38” long steel column that has a 1.5 in..
Piston-cylinder assembly in an air atmosphere : A piston-cylinder assembly in an air atmosphere of p = 1 atm (= 1.013 bar) contains 1 kg of nitrogen. The initial volume of the nitrogen is 1 m^3, and its initial pressure is 1 atm. The side of the cylinder is heated such that the heat transfer to th..
Slowly reduce the frequency to the point of synchronisation : Why do you think it is important, when using a stroboscope, to start at a very high frequency and slowly reduce the frequency to the point of synchronisation?
Gas behaviour and no change in kinetic or potential energy : A closed, rigid tank fitted with a paddle wheel contains 0.1kgof air, initially at 300 K, 0.1MPa. The paddle wheel stirs the air for 20 minutes, with the power input varying with time according to W = -10t, where W is in watts and t is time, in minut..
Determine the heat transfer for both cases : Liquid propanol at 250C is burned with air at the same temperature in an atmospheric pressure combustor operating at steady conditions. Products of combustion are cooled to a temperature of 250C. Enthalpy of formation of liquid propanol = -301,000 kJ..
Explain about research study: primary & secondary research : When conducting a Research Study, what are the advantages and disadvantages when using Face-to-Face interview as Primary Research method.
Explain the usefulness of lp : The production manager of a large Cincinnati manufacturing firm once made the statement, "I would like to use LP, but it's a technique that operates under conditions of certainty.
The stock brokerage firm : The stock brokerage firm of Blank, Leibowitz, and Weinberger has analyzed and recommended two stocks to an investors' club of college professors.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Calculate the power required to run the refrigerator

the fluid used is r-134a. the flow of r-134a is 70 lbmmin. if r-134a enters a compressor at -10 deg f and is a

  A bullet of mass 81gm and moving with a velocity of 300msec

a bullet of mass 81gm and moving with a velocity of 300msec is fired into a log of wood and it penetrates to a depth of

  Determine the mass flow rate and the rate of heat transfer

R134a flowing at 12 m/s enters a 25 mm diameter tube at a quality of 15%, at 36 Celsius and exits the tube at 10 bars as a saturated liquid. Determine (a) the mass flow rate of the R134a in kg/s, (b) the velocity of the R134a at the exit in m/s and (..

  Determine the maximun concentrated load

determine the maximun concentrated load that can be applied at the midpoint of a 3-m simple span. Neglect the weight of the beam.

  Determine the efficiency of a single fin

A radiator wall measuring 2 m by 3 m (WxH) is held a temperature of 125 °C. Straight aluminum fins (k = 175 W/mK) are to be mounted on the wall. The fins are 5 cm in length and 0.8 mm thick. The system is allowed to convectively transfer heat to ambi..

  What is the net positive suction head

In a chemical plant liquid ammonia is stored in a large tank at 72 degrees F and 200 psig. Ammonia is pumped from this tank to a smaller tank for chemical process usage. The pump used to supply ammonia to the process tank is located 12 ft above the s..

  About the earth temperature

The diameter of the sun is 1.39 x 106 km and is assumed to radiate with emissivity, e = 0.98, estimate its effective temperature. The distance between the sun and earth is about 1.495 x 108 km. The earth temperature is about 15 C. The solar constant ..

  Determine the rate of entropy generation during this

a 2-kw iron is left on the ironing board with its base exposed to the air at 25 degc. if the surface temperature is 500

  Determine the value of the polar coordinates of the point

A particle moves along a spiral described by the equation r=r(inital)+kappa*theta, where r(inital) and kappa are constants, and where theta is in radians. Assume that theta dot =alpha*time, where alpha= 0.15rad/s^2 and t is time expressed in seconds.

  Using the agma refined approach calculate the tooth bending

a 10-pitch 20-degree full-depth involute gearset with qv10 and a face width of 1.25 inches is being proposed to provide

  Steam flows through a horizontal adiabatic throttle which

steam flows through a horizontal adiabatic throttle which controls the flow to 25.0 ft3s and then through an adiabatic

  A rod has a cross sectional area of 1 cm2 the material has

a rod has a cross sectional area of 1 cm2. the material has the following strength characteristics beyond which the rod

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd