Friction between the piston and the cylinder is neglible

Assignment Help Mechanical Engineering
Reference no: EM13699713

A piston-cylinder assembly fitted with a spring. The cylinder contains water, initially at 538oC, and the spring is in a vacuum. The piston  face, which has an area of 125 cm2 , is initially at x1=50 cm. The water is cooled until the piston face is at x2=40 cm.
The force exerted by the spring varies linearly with x according to F=kx where k=350 N/cm. Friction between the piston and the cylinder is neglible. For the water determine
a. The initial and final pressures, and the amount of water present
b. Work and heat transfer

Reference no: EM13699713

Questions Cloud

How far from the central bright spot : In a double-slit experiment, the third-order maximum for light of wavelength 500nm is located 12mm from the central bright spot on a screen 1.5m from the slits. How far from the central bright spot will the second-order maximum of this light be loc..
Calculate h2asc, hasc^- : Problem- Ascorbic acid (H2C6H6O6 or HAsc), known as vitamin c, is a diprotic acid (Kal= 1.0 x 10 ^-5 and Ka2= 5 x 10 ^-12) found in cirus fruit. Calculate [H2Asc], [HAsc^-], [Asc^2-], and the pH of 0.050M H2Asc. Please break down the steps so I kn..
What is the total distance her car travels : An Automobile is traveling on a long, straight highway at a steady 76.0 mi/h when the driver sees a wreck 180m ahead. What is the total distance her car travels before it comes to a stop
Determine the horizontal distance traveled by the bullet : A bullet is fired from a rifle that is held at 1.6m above the ground in a horizontal position. The initial speed of the bullet is 600 m/s. Determine the horizontal distance traveled by the bullet
Friction between the piston and the cylinder is neglible : A piston-cylinder assembly fitted with a spring. The cylinder contains water, initially at 538oC, and the spring is in a vacuum. The piston  face, which has an area of 125 cm2 , is initially at x1=50 cm.
Evaluate the ratio numerically for a hydrogen atom : An atom of mass m is initially at rest with respect to an outside observer and has an electron in an excited state. Evaluate the ratio numerically for a hydrogen atom
Find the magnitude of the velocity of the canoe : A canoe has a velocity of 0.52m/s southeast relative to the earth. The canoe is on a river that is flowing 0.50 m/s east relative to the earth. Find the magnitude of the velocity of the canoe
How many centimeters were cut off the end of the second pipe : A pipe open at one end only has a fundamental frequency of 228 Hz. How many centimeters were cut off the end of the second pipe
Explain an organic acid whose salts are used to retard mold : Problem- Propanoic acid (CH3CH2COOH or HPr) is an organic acid whose salts are used to retard mold growths in foods. What is the [H3O+] of 0.10 M HPr? Ka=1.3 x 10^-5.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd