Freshwater is impounded to a height

Assignment Help Mechanical Engineering
Reference no: EM13706004

Freshwater is impounded to a height of 11 ft behind a dam as shown. Determine the magnitude and location of the resiltant force on the 4-ft by 4-ft gate.

a) There is no water on the right side of the gate.

b) Water on the right side of the gate has risen to height of 3 ft

Reference no: EM13706004

Questions Cloud

What is its spring constant : A 10kg block sliding along a frictionless surface with a velocity of 10m/s comes into contact with a horizontal, uncompressed linear spring. If the spring slows the block down to 0 m/s while being compressed a total of 30 cm, what is its spring const..
Gear is put in neutral on level road without wind resistance : The rolling resistance of a 1200kg car depends on its weigh as F = 0.006m x gravity. How far will the car roll if at 90km/h the gear is put in neutral on a level road without wind resistance?
Determine the power required-in watts to compress the spring : The force F required to compress a spring a distance x is given by F - Fo = kx where k is the spring constant and Fo is the preload. Determine the work required to compress a spring, whose spring constant is k = 37 kN/m, a distance of 2 cm starting f..
Define a function m-file that calculates the displacement x : The following suspension system has two support structures-a spring and a rubber pad. Vertical force F (N) acts on the moveable plate. The spring has a spring constant of k1 = 1000 N/m. The rubber pad has a spring constant of k2 = 20000 N/m. The rubb..
Freshwater is impounded to a height : Freshwater is impounded to a height of 11 ft behind a dam as shown. Determine the magnitude and location of the resiltant force on the 4-ft by 4-ft gate.
Find the eigen values of the state matrix a : Given the following differential equation: 4x'''+3x''+7x'+4.6x=5sin(t), Derive the state space representation. Derive the characteristic equation.
Determine the specified property at the indicated state : For H2O, determine the specified property at the indicated state. Locate the state on a sketch of the T-v diagram. (A) T=140 degree Celsius, v=.5 m^3/kg. Find p, in bar (B) p=30 MPa, T=100 degree Celsius. Find v, in m^3/kg (C) p=10 MPa, T=485 degree ..
Exact location of points that appear in two dimensional plot : Determine one by one the exact location of the points that appear in the two dimensional plot of fig 2.8. How many different paths can the system follow from state a to state b (chapter 2, advanced engineering thermodynamics by began)
Block sliding along a frictionless surface with a velocity : A 10kg block sliding along a frictionless surface with a velocity of 10m/s comes into contact with a horizontal, uncompressed linear spring. If the spring slows the block down to 0 m/s while being compressed a total of 30 cm, what is its spring const..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd