Frame analysis and represent the moments

Assignment Help Civil Engineering
Reference no: EM13870372

Figure below shows a "sway" frame with 14×14 inch columns and 14×26 in beams. The moments computed for column AB are from the frame analysis and represent the moments about x-x axis of the column cross section.

Mxuns=650 in.kips, Mxus = 110 in-kips and Pu = 105 kips.

In the direction perpendicular to the plane, the framing is considered as "no-sway" and theoretically, there is no moment transferred to the column; thus use the minimum amount of moment based on emin (however, you will need to use magnification factor for this moment also).

Use βd = 0 for the "sway" frames and 0.4 for "no-sway" frames for all calculations. Use Cm=1 when computing the magnification factor for the moment with respect to y-y axis of the column.

fy = 60,000 and f'c = 4,000 psi.

1. Compute the design moment with respect to the x-x axis of the cross section.

2. Compute the design moment with respect to the y-y axis of the cross section.

3. Using the results from Parts 1 and 2, check if the column design is acceptable using Breseler's equations

1710_Compute the design moment.jpg

Reference no: EM13870372

Questions Cloud

Draw an analogy to similar costs incurred for employees : Discuss whether companies should capitalize or expense the money paid to employees who evaluate requests for use of their logos and who search for instances where the companies' intellectual property has been used without permission. Draw an analogy ..
Draw the consumers demand curve for griffie of type : Fix the prices of types .3 and .7 at 3 and 4, respectively. Draw this consumer's demand curve for griffie of type .5 as a function of the price of this type of griffie.
Prepare the journal entry to record the sale of the shelving : The shelves originally cost $ 6,400 and had been depreciated on a straight- line basis over an estimated useful life of 10 years with an estimated residual value of $ 400. Assuming that depreciation has been recorded to the date of sale, show the eff..
Frame analysis and represent the moments : Figure below shows a "sway" frame with 14×14 inch columns and 14×26 in beams. The moments computed for column AB are from the frame analysis and represent the moments about x-x axis of the column cross section.
Show that monopoly passes on more than full cost increase : Suppose that demand takes the form X = p-a for a > 1. Show that the monopoly passes on more than the full cost increase to consumers. (That is, dp(e)/ de > 1.)
Complete a depreciation schedule for straight line method : Complete a depreciation schedule for each of the alternative methods. a. Straight line. b. Units of production. c. Double declining balance. 2. Assume NGS sold the hydrotherapy tub system for $ 2,100 at the end of year 3. Prepare the journal entry to..
What is the best general nondiscriminatory scheme : Go back to the parameterization of problem 3. What is the best general nondiscriminatory scheme from the point of view of the manufacturer?
Preparations to file for a npdes permit : The ABC Tannery has asked you to assist them in preparations to file for a NPDES permit to discharge wastewater into the XYZ River. The Dept. of Natural Resources water quality criterion for the XYZ River is 5.00 mg/L of DO.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine what are the major nutrients required for growth

What are the major nutrients required for growth of microbial population in wastewater treatment plants. List the major differences and similarities between hetrotrophic bacteria and nitrifying bacteria.

  Calculate both volumetric molar and mass afr

Compare the stoichiometric air/fule ratios (AFR) for complete combustion of Benzene (C6 H6), Octane (C8 H8), and Ethanol (C2 H5 OH) in air (O2 + 3.76 N2). The only products should be CO2, H2O and N2.

  Determine the elongation of the plate under a tensile load

a flat steel plate of 10mm thickness varies in width from 150mm to 300mm over a length of 1.5m. Determine the elongation of the plate under a tensile load of 250KN

  Determine the moment of the forces around point a

The frame ACD is hinged at A and D and is supported by a cable that passes through a ring at B and is attached to hooks at G and H. If the tension in the cable is 1125 N (thus 1125 N in section BG and 1125 N in section BH)

  Explain the reason for the variation of the water

A homogeneous coarse sand deposit has a water table at 10 m depth. The water coefficient of permeability of the sand is found to vary significantly with height above the water table even though the sand deposit is homogeneous

  What is length of consecutive wet days that has a occurence

Assuming that the number of days until the next dry day is geometrically distributed, what is the length of consecutive wet days that has a probability of occurence of no more than 0.05

  Describe a soil classified as sw and a soil classified as ch

Describe a soil classified as SW and a soil classified as CH in the Unified Soil Classification System as you would to a person having no knowledge of soil classification procedures or equipment.

  Determine the maximum resisting moment mr that the beamcan

The maximum flexural stress on a transverse cross section of a beam2" x 4" with a rectangular cross section must not exceed 8 ksi.Determine the maximum resisting moment Mr that the beamcan support if the neutral axis is

  Select the sentence that is punctuated correctly

Select the sentence that is punctuated correctly.

  What are the values of its density specific volume

A certain gas weighs 16.0 N/m3 at a certain temperature and pressure. What are the values of its density, specific volume, and specific gravity relative to air weighing 12.0 N/m3 ?

  What mass of petcock should be used to maintain a pressure

What mass of petcock should be used to maintain a pressure of 100 kPa gage for a cross-sectional area of 4 mm2 at the opening? Atmospheric pressure is 100 kPa.

  Determine if the process is possible from the second law

Steam at 800kpa and 300 degree celsius exists in the large supply line. when the valve opened from the large supply the steam enters into an empty, evacuated tank with a volume of 0.3m cube

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd