User Account

All Pages

Force requiring lateral bracing in platform building

Assignment Help Civil Engineering
Reference no: EM132416153

Question 1. Which of the following is distinguishes platform framing over balloon framing?

a. It is the more recently developed wood framing system

b. It is easier to erect

c. It is the primary light framing system used today

d. It settles considerably more as wood dries and shrinks

e. All of the above

Question 2. Which of the following is not a force requiring lateral bracing in platform building?

a. Gravity

b. Wind

c. Seismic

d. b. and c.

e. None of the above

Question 3. At what point exterior finishing operations can interior finishing operations begin?

a. After the eaves and rakes are finished

b. After the exterior windows and doors are installed

c. After the exterior walls are safely sheltered from sun, wind and rain

d. All of the above

Question 4. Which of the following are primers for the exterior of a building clad in wood siding?

a. Masonry primer

b. Exterior latex or alkyd primer

c. Block filler primer

d. Oil stain

Question 5. A vapor barrier is a material placed on the cold side of thermal insulation to prevent water vapor from diffusing into the insulation where it could condense into liquid?

a. True

b. False

Question 6. Which of the following is not a typical element in the design of a stair?

a. Stringer

b. Riser

c. Handrail

d. Rafter

e. Tread

Question 7. A disadvantage of a low-slope roof is which of the following?

a. Can over large horizontal dimensions economically

b. Geometry is relatively simple

c. Can be used as walking surfaces

d. Water accumulates and drains slowly

e. None of the above

Question 8. Which of the following is disadvantage of singleply roof membranes versus bituminous roof membranes?

a. Require more onsite labor

b. Less elastic

c. Lack redundancy

d. Less vulnerable to leaking

e. All of the above

Question 9. "single-strength" glass is typically used in which of the following conditions?

a. Where high windloads are expected

b. For windows in taller buildings

c. For windows in smaller buildings

d. For windows with larger lites

e. For windows in seismic areas

Question 10. Which of the following glazing assemblies reflects and radiates the largest porition of sunlight back to the outdoors?

a. Double glazing with reflective coating on the inner glass surface

b. Clear float glass

c. Reflective glass

Reference no: EM132416153

Questions Cloud

Research paper on typhoid fever-what is the disease : Research paper on typhoid Fever. What type of research has been done about the Disease. What is the disease
Explain what might be the best type of member : Explain what might be the best type of member (ie what cross section shape) for effectiveness and cost, and explain why.
How much should he save money with the addition of workers : If the liquidated damages is Php2,000 per day of delay, and the men are paid Php80 per day, will the engineer be able to complete the job on time?
ENGR 206 Fundamental of Electrical Engineering Assignment : ENGR 206 Fundamental of Electrical Engineering Assignment Help and Solution, University of North Dakota, USA. Laboratory - Analysis of Simple Resistive Circuits
Force requiring lateral bracing in platform building : Which of the following is not a force requiring lateral bracing in platform building?
Differences in clinical quality and customer service quality : Can you explain the differences between clinical quality and customer service quality? how they would benefit your facility when implemented properly?
Find the composite value of manning : Find the composite value of Manning's n using the four methods given in this chapter if the flow epthis 3.0 ft
Different construction contracts for analysis : If you have three different construction contracts for analysis, their differing and/or unforeseen site condition clause, the course of actions
Difference between point mutation and frameshift mutation : Compare the difference between a point mutation and a frameshift mutation. Describe the different between vertical gene transfer and horizontal gene transfer:

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculate the pressure drop to process pregelatinized starch

A single screw extruder is being used to process pregelatinized starch. The screw dimensions are as follows: channel width 3 cm, channel height 0.5 cm and screw length 50 cm. The wall velocity is estimated to be 0.31 m/s.

  Determine the required depth of cut

A work bar with a 4.5-in diameter and 52-in length is chucked in an engine lathe and supported at the opposite end using a live center. A 46M-in portion of the length is to be turned to a diameter of 4.25 in one pass at a speed of 450 ft/min.

  Determine the reactor basin volume

An activated sludge plant is to be designed for a population of 4000 persons. The influent flow is 380 Lpcd and the influent BOD5 is 200 mg/L. Pertinent data are: Primary clarifier removes 33% of the influent BOD5, and the state regulatory agency all..

  Which of these materials are likely to be retained

A waste mixture contains a variety of volatile organic compounds, nonvolatile organics, metals, and sandy soil. In a vitrification treatment,

  What is the rate constant for undergraduate students

A reaction of great significant for undergraduate students is the fermentation of sugar with yeast. This is a zero order (in sugar) reaction, where the yeast is a catalyst (it does not enter into the reaction itself).

  Calculate the amount you will have from this investment

You have just received $10,000 witch which you can do anything. You have decided to invest the money over a long period of time and then use it to make a down payment on a vacation home.

  Find which is produced with emphasis on temporal distributn

You are assigned the task of using bioremediation to cleanup a hazardous waste site contaminated with Tetrachloroethylene. The site is a shallow surficial sandy aquifer 30 feet deep underlain by a clay unit. The depth to the watertable is 10ft.

  Calculate what will be the total emissions of pm and pm10

emissions from waste oil combustion may be estimated using ap-42 1.11. A small boler is operated from 10/15/2012 through 4/15/2013 and it is used to burn 45 gallons per hour of a blended waste oil having an ash content of 7%

  Draw the shear and moment diagrams,ensuring to label

The joists from the previousquestion are supported by concrete beams that are 300mm wide by 500mm deep. The concretebeams span 8.4m. Assume the beam is also simply supported. The weight of the joistis 1.04 KN/m.

  Compare your results with the true value of the derivative

We know that the molar concentration and volume of a solution is the sum of the product of the molar concentration and volume of each solution component before mixing

  Determine the allowable length of the penstock

The bracket ABC can be supported in the eight different ways shown. All connections consist of smooth pins,rollers, or short links. For each case, answer the questions listed in Prob.4.59,and, whenever possible

  Determine principal stress and maximum in plane shear stress

The internal loadings at a section of a beam consist of an axial force of 6 kip, and a moment of 5 kip-ft. Determine the principal stress and maximum in plane shear stress at points A,B,and C.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd