Force required to keep the cart moving at constant velocity

Assignment Help Mechanical Engineering
Reference no: EM13701060

A 2 cm horizontal jet of water with a velocity of 15 m/s is spraying onto a vertical plate attached to a cart moving opposite the direction of the water jet at 8 m/s. Determine the force required to keep the cart moving at a constant velocity. What is the power supplied to the cart? Assume the water splashes in all directions in the plane of the plate upon impact.

Reference no: EM13701060

Questions Cloud

Compute the force needed to completely submerge the object : Calculate the 2x4 Block's Weight, mass, density and Specific Weight. Express values in both metric and US units. Compute the force needed to completely submerge the object.
Low-speed wind tunnel with atmospheric air : A fan that can provide air speeds up to 50 m/s is to be used in a low-speed wind tunnel with atmospheric air at 25°C. If one wishes to use the wind tunnel to study flat-plate boundary layer behaviour up to Reynolds numbers of Rex = 10^8 , what is the..
Where the hydrodynamic boundary layers meet : Air at 20°C flows at 1 m/s between two parallel flat plates spaced 5 cm apart. Estimate the distance from the entrance where the hydrodynamic boundary layers meet.
What is the equation for the actual air temperature : An electric heater heats air. The temperature sensor has a time constant of 5 seconds. The air temperature output (in °C), as measured by the temperature probe is: T=200+cos(0.5t)
Force required to keep the cart moving at constant velocity : A 2 cm horizontal jet of water with a velocity of 15 m/s is spraying onto a vertical plate attached to a cart moving opposite the direction of the water jet at 8 m/s. Determine the force required to keep the cart moving at a constant velocity.
Distillery uses mechanical vapour re-compression : The wash still in a whisky distillery uses mechanical vapour re-compression as shown in the simplified diagram of the Figure shown below. The vapour from the still is at 80° C. Take a minimum temperature difference between the vapour leaving the stil..
Provide a theoretical analysis and treatment recommendation : Case Study Development and Theoretical Explanation - Provided a theoretical analysis and treatment recommendation for the case. The treatment selected flows logically from the theory utilized.
What tax basis does samson take in the devon net assets : What tax basis does Samson take in the Devon net assets and how does Devon use Section 337 to create a nonrecognition gain transaction when Devon transfers appreciated assets to Samson.
Analyse the current financial state of anthonys orchard : Analyse the current financial state of Anthony's Orchard and evaluate the impact of a major customer cancelling their expected order.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The ammonia is then cooled until its pressure drops to 10

a constant-volume tank contains 10 lbm of ammonia initially at 30 lbfin2 and 80degf 539.67degr. the ammonia is then

  If the true mean is really 20 what sample size must be used

suppose we wish to test the hypotheses ho u15 h1 u does not 15 where we know that sigma2 9.0. if the true mean is

  What is the angular velocity wcd

What is the angular velocity Wcd (t)?

  Two steel plates a572 fy 50ksi are welded together to form

two steel plates a572 fy 50ksi are welded together to form an inverted t-beam. determine the maximum bending stress

  Heat is added to the water at a rate of 500 w how long

a pot containing 1.0 liters of water at 20 degc is placed on the stove and heat is added to the water at a rate of 500

  You are holding a book against a vertical wall by pushing

pushing a book against the wall.you are holding a book against a vertical wall by pushing upwards with your hand. the

  Cylinder device nitrogen gas executes a carnot power cycle

In a sealed piston cylinder device Nitrogen gas executes a CARNOT POWER CYCLE. The source and sink temperatures are 999 K and 333 K. Minimum pressure in the cycle is 20 kPa. The minimum volume is (1/40) of the maximum volume in the cycle. The cycle w..

  Find the x-component of the vector a -b for the previous

two vectors a with magnitude 32.0 units directed at an angle of 56.0 deg above the x-axis and b 32.0 units long

  Consider a plate with uniform heat generation q for k200

consider a plate with uniform heat generation q. for k200 wmk q40 mwm3. t1160 c at x0 t2100 c at x2l and a plate

  Determine the net work of the cycle in kj and the heat

a gas within a piston-cylinder assembly undergoes a thermodynamic cycle consisting of three processesprocess

  For the following given states find the reguired region ie

for the following given states find the reguired region i.e. phase or property of water.a given p 400kpa v 0.001084 m3

  If the cooling water enters at a temperature of 20 degree c

one way to decrease the power needed to compress a gas using a compressor is to encompass the compressor in a water

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd