For these conditions what is the force in units of lbf and

Assignment Help Mechanical Engineering
Reference no: EM13644933

Consider a subsonic engine inlet (i.e., a diffuser) with an inlet area of 2300 in2, and an exit/inlet area ratio of 1.44. Air enters the diffuser flowing at 10 lbm/s with a static pressure of 5 psia and a velocity of 120 m/s. The gases exit the diffuser at a state pressure of 5.4 psia and with a velocity of 78 m/s. You should assume the ambient external pressure on the wall of the diffuser is 5.5 psia.

a.) For these conditions, what is the force (in units of lbf and N) transmitted to the structure holding the diffuser? Provide both direction and magnitude of the force, and use a picture to help present your answer.

b.) Based solely on your results, comment on whether the force acting on the diffuser would help speed up or slow down a vehicle that used this diffuser as part of a jet propulsion system.

Reference no: EM13644933

Questions Cloud

What is the heat transfer rate per unit length if a 10 mm : a stainless steel tube k 14 wmk used to transport a chilled pharmaceutical has an inner diameter of 36 mm and a wall
What is the actual ground-state electron configuration for : what is the actual ground-state electron configuration for copper cu? since copper is an exception to the usual order
A force holds them in place so that their centers are : two metal balls of mass m1 3 g diameter 3 mm and m2 4 g diameter 4 mm have positive charges of q1 4 nc and q2 5
A spark causes the cs2g to ignite burning it completely : a mixture of cs2g and excess o2g is placed in a 10.0l reaction vessel at 100.0 celsius and pressure of 3.oo atm. a
For these conditions what is the force in units of lbf and : consider a subsonic engine inlet i.e. a diffuser with an inlet area of 2300 in2 and an exitinlet area ratio of 1.44.
There are 40 students in an elementary statistics class on : there are 40 students in an elementary statistics class. on the basis of years of experience the instructor knows that
The gun swings up to a height of 183 centimeters what was : a dart gun suspended by strings hangs in equilibrium. the mass of the gun is 355 grams not including a dart. the gun
Asoluble iodide was dissolved in water then excess of : asoluble iodide was dissolved in water .then excess of silver nitratewas added to precipitate all the iodide gave ions
The asteroid hits the earth nearly tangentially in the : the earth has an angular speed of 7.272 x 10-5 rads in its rotation. find the new angular speed if an asteroid m 1.12

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd