For the following signals 1024 points were sampled

Assignment Help Mechanical Engineering
Reference no: EM13626261

For the following signals, 1024 points were sampled.

a) 621 Hz signal sampled at 850 Hz

b) 1072 Hz signal sampled at 1600 HZ

c) 1143 Hz signal sampled at 450 Hz

Determine:

i) The Nyquist frequency

ii) The minimum sampling rate to avoid aliasing

iii) The frequency step size of the FFT and the uncertainty in the frequency

iv) the aliased frequency (Besure to round off your answers to the nearest frequency step)

Reference no: EM13626261

Questions Cloud

A body of mass 3kg with an initial velocity of 2 ms makes : a body of mass 3kg with an initial velocity of 2 ms makes an elastic collision with another body m2 2kg at rest.finda.
Calculate the flame temperature of normal octane liquid : calculate the flame temperature of normal octane liquid burning in air at an equivalence ratio of 0.5. assume there is
Two charges repel each other r with a force of 10 -6n when : two charges repel each other r with a force of 10 -6n when they are 10 cm apart. when they are brought closer together
Consider a carnot-cycle refrigerator with ammonia as the : consider a carnot-cycle refrigerator with ammonia as the working fluid. heat is rejected from the ammonia at 20 deg c
For the following signals 1024 points were sampled : for the following signals 1024 points were sampled.a 621 hz signal sampled at 850 hzb 1072 hz signal sampled at 1600
What is the suction specific speed for the pump that is : what is the suction specific speed for the pump that is operating under the conditions given in problem 14.16? is this
A 500 kw compressor is being designed to operate on air in : a 500 kw compressor is being designed to operate on air in a space where the temperature is 300 k and pressure is 90
You are driving north on 107th avenue at a speed of 292 : you are driving north on 107th avenue at a speed of 29.2 mph. a police car whose siren produces a sound at a frequency
Give a 95 confidence interval for the differences in the : in 2006 merck released a vaccine named gardasil for hpv - the most common cause of cervical cancer among young women.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A balloon behaves so the pressure is p c2v13 c2 100 kpam

a balloon behaves so the pressure is p c2v13 c2 100 kpam. the balloon is blown up with air from a starting volume of

  What will be the charge on the capacitor a long time after

capacitor with capacitance 6.00 microf is connected to a resistor with r 780 o in series and an emf source of 25.0 v

  To what elevation in m would a 1000-kg mass have to be

a domestic water heater holds 189 l of water at 60 degrees c 1 atm. determine the exergy of the hot water in kj. to

  Air at -55 f 4 psia and m25 enters a constant area

air at -55 f 4 psia and m2.5 enters a constant area isentropic process and leaves the isentropic process at m0.2

  What are the commpressive stresses induced by thermal

what are the commpressive stresses induced by thermal expansion in a cs pipe lined with a zirconium tube that is

  Find the diameter of a pipe to convey

Find the diameter of a pipe to convey the superheated steam flowing into the mixing process if the speed of the steam is 20m/s and also ascertain the condition of the resulting mixture.

  Determine the acceleration of the piston

Knowing that crank AB rotates about point A with a constant angular velocity of 900 rpm clockwise, determine the acceleration of the piston P when θ = 120°.

  The pan is hot 80c and the room is cool 20c calculate the

a hot surface on a stovetop faces upwards. it is a pan whose diameter is 10 inches. the surface of the pan is dull with

  The water level in the dam is upto the brim of the wall

one of the walls of a dam is at 67 degrees to the horizontal. the wall is 8 m long and 40 m wide. density of the water

  Assume constant specific heats where cwater 4179 kjkg-k

initially an insulated rigid tank contains 15.65 kg of water at 24.16oc and 101 kpa. the tank also contains a 3.12 kg

  What is the maximum constant speed in miles per hour a

what is the maximum constant speed in miles per hour a stock car can travel around the 1000 ft radius turns that are

  Discuss how u would design a drive shaft based on the

torsion lab using aluminum cylinderical specimens1 how would a hollow cylindrical specimen of the same lenght and mass

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd