For plain carbon steel and convection

Assignment Help Mechanical Engineering
Reference no: EM13713211

For plain carbon steel and convection (h=50 W/m^2 K) to air at 500K, Ti=300k, with a slab geometry 0.2 m thick (2L), find:

a) Boat Number

b) For a Fourier number (based on l=0.1m) of 0.1, is the tearm series valid? Find the time

c) If the one term solution is valid determine the surface temperature, if not valid, use the semi-infinite solution to find the surface temperature 5.

A vertical plate, 200mm high by 500mm, wide has one side exposed to condensing saturated water vapor at 1 ATM. If 10kg/h is to be condensed, determine:

a. the surface temperature (to condense 10 kg/h)

b. the rate of heat transfer

Reference no: EM13713211

Questions Cloud

Manufacturing space with an average floor to ceiling height : A large manufacturing space with an average floor to ceiling height of 30 ft has a floor area of 5000 ft^2. The total infiltration rate for the space is estimated to be 1.5 air changes per hour. The inside design temperature and relative humidity are..
What is the initial velocity of the rock : A rock is thrown vertically up to the air. It reaches a maximum 15 m above the point where it was released. What is the initial velocity.
Importance of structural mechanics in mechanical engineering : Briefly discuss the importance of Structural Mechanics in Mechanical Engineering? List four different types of loadings that can be applied on mechanical structures or components
Find the rms speed of the oxygen molecules in the air : At what Kelvin temperature does the rms speed of the oxygen (O2) molecules in the air near the surface of the earth become equal to the escape speed from the earth
For plain carbon steel and convection : For plain carbon steel and convection (h=50 W/m^2 K) to air at 500K, Ti=300k, with a slab geometry 0.2 m thick (2L), find Boat Number. For a Fourier number (based on l=0.1m) of 0.1, is the tearm series valid? Find the time
Each cord for the system to be in equilibrium : If the box weighs 200 lbs, what force must be in each cord for the system to be in equilibrium? Cable AB is 1.5m and the vertical distance from B to A (marked as "y") is 0.75m
Temperature of the liquid is uniform that only changes time : You like to drink your mixture of coffee and cream very hot. However, it takes you 15 minutes to walk from the coffee house to your office, so you wonder when is best to mix the cream to the coffee. Your favourite mix is half-half, that is, half mug ..
The diameter of largest solid sphere for lumped behavior : For plain carbon steel, with properties at 300K in the Appendix and convection (h=50 W/m^2 K) to air at 500K, determine the diameter of largest solid sphere for lumped behavior (2 part- show equivalent length is D/6 and that D for Bi
How is the terminal velocity impacted : Consider an object falling through air. How is the terminal velocity impacted when certain physical properties are changed, let us define.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd