For network of given figure find the currents i1 and is

Assignment Help Electrical Engineering
Reference no: EM131203636

For the network of given figure:

a. Find the currents I1 and Is.

b. Find the voltages Vs and V3.

1099_Network.jpg

Reference no: EM131203636

Questions Cloud

List all the functional dependencies exist in the relation : Select any two (2) of your relations from the previous step, 1a), and perform the following for each of those two relations: List all the functional dependencies exist in the relation. Demonstrate that the relation meets Third Normal Form (3NF)
Currently sells gourmet coffee through multiple outlets : Jumping Java Inc. currently sells gourmet coffee through multiple outlets. You are a consultant, and the company is asking you for guidance for two possible plans, A or B, for expanding sales. Plan A: Jumping Java would begin selling additional produ..
What is the opportunity cost of petes : Introduction to Microeconomics Problem Set - Is this farm able to produce 12,000 bushels of corn and 8,000 bushels of soybeans? What does this combination of output suggest about the use of resources?
Does shuttlecock make me feel uncomfortable and endangered : Does the shuttlecock make me feel uncomfortable and endangered? Does this work of art make me laugh? If so, why am I laughing? What meaning does the odd use of scale and proportion give to the sculpture?
For network of given figure find the currents i1 and is : For the network of given figure: - Find the currents I1 and Is. -  Find the voltages Vs and V3.
Nominal growth rate of the economy : Pick 4 and calculate their expected returns using a simple "Gordon growth model" and using the nominal growth rate of the economy for the company growth rate. Discuss your assumptions and findings.
Manufactures and sells custom-made windows : Woodland Industries manufactures and sells custom-made windows. Its job costing system was designed using an activity-based costing approach. Direct materials and direct labor costs are accumulated separately, along with information concerning three ..
Find the voltage output of a dynamic microphone : A microphone of 300Ω impedance has an output at -60 dB below a 1 mW reference level. The microphone provides input to an amplifier which in turn is to provide an output level of 30 dBm when a load of 8 Ω is connected to the output terminals of the..
Process of designing and developing this mini online course : List two (2) assignments: (a) an essay test with three (3) questions and (b) a writing assignment. Discuss at least two (2) challenges and two (2) benefits with the process of designing and developing this mini online course.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Calculate the sending in voltage

The resistance is 0.03 Ohms per phase per km and the line inductance is 0.7 millihenry per phase per km.- calculate the sending in voltage-the voltage regulation.

  What is the overall delay from the continuous-time input

What is the overall delay from the continuous-time input to the continuous-time output (in seconds) of the system in Figure P7.22?

  Rc ciruit current course 3u-t a in parrallel to 6k ohm

rc ciruit current course 3u-t a in parrallel to 6k ohm resistor and 5uf cap. determine the instantaneous power

  Design a current mirror that produces i1 and i2

An integrated circuit employs the source follower and the common-source stage shown in Fig. 9.37(a). Design a current mirror that produces I1 and I2 from a 0.3-mA reference.

  Compute and plot the 128 point fft of a 0.125hz cosine wave

Compare the differences in the FFT result. Explain why even though the inputs to both FFTs are the same cosine waves, the shapes of the FFTs are different.Compute and plot the 128 point FFT of a 0.125Hz cosine wave

  Which should be the signal power in the given case

A cable technician tested the signal-to-noise ratio on the curb as 20 dBm. This means, if the noise power is at 1 mW, then the signal power should be 20 dB higher then that. If the noise power is 20 mW

  Determine density of mobile charge at semiconductor surface

The silicon substrate is N-type (doping level ND = 7x10^16cm-3), and the gate is heavily doped N+-type polysilicon. Assuming zero oxide charge density, determine the density of mobile charge at the semiconductor surface, if the voltage applied bet..

  What is the resulting vertical break voltage for the diode

Determine the piecewise equivalent resistance for the vertical rise section of the characteristics.

  Determine the torque developed by the motor

If the motor is operating in a linear region, determine the torque developed by the motor

  Determine how many address pins does the dram have

A 1GB DRAM uses 4-bit data and has equal-length row and column addresses. How many address pins does the DRAM have?

  What are the values of current gain and voltage gain

A current amplifier with R=9 kohm Ro=1 kohm and Ais=100 is connected between a 8 V voltage source with a source resistance of Rs=1 Kohm and a load resistance of RL=9 Kohm.

  Design the circuit using one input or and and gate

A combinational logic circuit has four imputs (A, B, C, and D)and one output Z. The output is 1 iff the input has three consecutive 0's or three consecutive 1's. Fore example, if A= 1, B = 0, C = 0, and D = 0, then Z = 1, but if A = 0, B = 1, C =0..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd