For mating hinges on the sign specify the class of fit the

Assignment Help Mechanical Engineering
Reference no: EM13613154

An advertising sign is suspended from a horizontal rod and is allowed to swing under wind forces. The rod is to be commercial bar stock, nominally 1.50 inches in diameter. For mating hinges on the sign, specify the class of fit, the limits of size, and the limits of clearance. Use the basic hole method. Also, explain the difference if you were asked to use the basic shaft method.

Reference no: EM13613154

Questions Cloud

With the power supply disconnected the dielectric material : a parallel-plate capacitor is made of two flat metal plates pressed against a thin slab of dielectric material. the
It has been argued on the grounds of conservatism that all : it has been argued on the grounds of conservatism that all intangible assets should be written off immediately after
An experiment was designed to compare several different : q.1 an experiment was designed to compare several different types of air pollution monitors. the monitor was set up and
Bamba corporations cost formula for its selling and : bamba corporations cost formula for its selling and administrative expense is 47900 per month plus 52 per unit. for the
For mating hinges on the sign specify the class of fit the : an advertising sign is suspended from a horizontal rod and is allowed to swing under wind forces. the rod is to be
Analyze the process of developing qualified workers and : analyze the process of developing qualified workers and make at least one recommendation for improvement that would
The electric potential at a position located a distance of : the electric potential at a position located a distance of 22.8 mm from a positive point charge of 8.00times10-9c and
From the video barcelona restaurant group - managing human : from the video barcelona restaurant group - managing human resources determine how the hiring practices at barcelona
A 117-cm-long 300g string oscillates in its n 3 mode with : a 117-cm-long 3.00g string oscillates in its n 3 mode with a frequency of 180hz and a maximum amplitude of 5.00mm.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  How the lubricants reduce the friction

How the lubricants reduce the friction and wear characteristics of the parts in contact?

  Determine the impulse of the golf club on the ball neglect

a man hits a 50g golf ball such that it leaves the tee at an angle of 40 degrees with the horizontal and strikes the

  Determine the following a pressure psi at each state b mass

a closed rigid tank contains 5 lbm of a two phase mixture of water initially at 260degf with a quality of 0.6. heat

  A tool with a weight of 500lb moves continuously from the

a cantilevered boom is part of an assembly machine. a tool with a weight of 500lb moves continuously from the end of

  A steel tape is used to measure a distance of 20 m at a 10

a steel tape is used to measure a distance of 20 m at a 10 0c. assuming that the tapenbspwill measure the true distance

  Air flows ocer the top and bottom surfaces of the plate and

a thin flat plate that is 0.2 m x 0.2 m on a side with rough top and bottom surfaces is placed in a wind tunnel so that

  How many pounds of downward pressure is placed

approximately how many pounds of downward pressure is placed on a piston in an internal combustion engine at the moment of ignition? I know this will vary some depending on the type fuel, the size of the combustion chamber and ect.

  A horizontal 500 lb force performs at a point d of

a horizontal 500 lb force performs at a point d of crankshaft ab which is held in static equilibrium by a twisting

  A heat engine operates in a carnot cycle between720degc

a heat engine operates in a carnot cycle between72.0degc and345degc. it absorbs21600j of energy per cycle from the hot

  Determine the velocity ratios that can be achieved

Determine the velocity ratios that can be achieved by the gear box in terms of number of teeth in the sun wheel  and determine which component (out of the sun wheel, planet carrier and annular wheel) has to be used as the input shaft to get the req..

  Determine the linear coefficients of expansion

What was the percentage error found between experimental and accepted values and what caused any errors, and how could they be minimised?

  Fluid mechanics boundary layer theory

Fluid mechanics boundary layer theory

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd