For a brief time the formula 1 championship held one of the

Assignment Help Mechanical Engineering
Reference no: EM13630558

Race cars often use wings in an effort to increase cornering speeds. The wings provide an extra downward force that increases the friction force available between the tyres and the road.

For a brief time, the Formula 1 championship held one of the races in the USA at the Indianapolis International Speedway. A part of the circuit utilised one of the banked corners that makes up the main oval track. This corner has a radius of curvature of ? = 350m and is banked at an angle of ???= 90.

By the rules, a Formula 1 car must weigh 640kg (including the driver), and an estimated coefficient of static friction between the tyres and the road is ?s = 1.5.

(a) Calculate the maximum speed that a Formula 1 car can travel around the banked corner without any down force.

(b) Calculate the maximum speed that a Formula 1 car can travel around the banked corner with a wing that provides a down force of; Where v is the speed of the car in m/s.

Reference no: EM13630558

Questions Cloud

Draw the shear and bending moment diagrams for the beam : draw the shear and bending moment diagrams for the beam and loading shown and determine the maximum normal stress due
A series of parcels is carried on a belt which goes over a : a series of parcels is carried on a belt which goes over a pulley with 600 mm diameter. if the belt starts from rest
Determine an expression for steady temperature : determine an expression for steady temperature distribution in a long hollow cylinder with specified surface
The 2kg block a and the 5kg block b are initially at rest : the 2kg block a and the 5kg block b are initially at rest on the inclined plane as shown. all surfaces in this system
For a brief time the formula 1 championship held one of the : race cars often use wings in an effort to increase cornering speeds. the wings provide an extra downward force that
Air as an idea gas is compressed from a state where the : air as an idea gas is compressed from a state where the pressure is 0.1 mpa and the temperature is 27oc to a state
Water at 25 degrees c enters a heat exchanger at 01 kgs and : water at 25 degrees c enters a heat exchanger at 0.1 kgs and exits at 50 degrees c. kerosene enters the other side of
Geography 4 assignments coastal geography that go along : 4 assignments coastal geography that go along with spreadsheet ltbrgt ltbrgtthese are the first 2 assignments it would
Integer expression evaluator this program must use stacks : this program must use stacks in order to evaluate integer expressions. your program need only implement the following

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd