Following the process after having obtained answers for b

Assignment Help Mechanical Engineering
Reference no: EM13626361

An isolated rigid container is divided into two compartments. Initially the divider is impermeable at a fixed location and insulated. Compartment A has VAo = 0.05 m^3, TAo = 753 K and 0.03 Kg of CH4. Compartment B has VBo = 0.20 m^3, TBo = 923 K & 0.05 Kg of N2.

a) With the wall fixed, impermeable & insulated what are the initial pressures of A & B?

b) If the wall allows for heat transfer between A & B what will the final temperatures of each side be? (Assume the divider remains at a fixed position.) At these temperatures determine the new pressures.

c) Following the process after having obtained answers for (b) the dividing medium is now allowed to move and the insulation is again replaced, preventing heat transfer. What are the final pressures and volumes of the two compartments? Hint: VAo + VBo = VA1 + VB1 = V & VB = V-VA

 

Reference no: EM13626361

Questions Cloud

A piston cylinder containing ar at some initial : a piston cylinder containing ar at some initial temperatureto is allowed to cool. once the volume of the cylinder
The needle has a magnetic moment of 0700 mjt what is the : you place a magnetic compass on a horizontal surface allow the needle to settle into its equilibrium position and then
A what is the probability that a randomly selected home run : a baseball player hit 67 home runs in a season. of the 67 home runs 20 went to right field 22 went to right center
What is the angular momentum of a figure skater spinning at : what is the angular momentum of a figure skater spinning at 4.5 revs with arms in close to her body assuming her to be
Following the process after having obtained answers for b : an isolated rigid container is divided into two compartments. initially the divider is impermeable at a fixed location
If the pressure in this fluid is just barely able to push : when a person is given intravenous fluid the bag containing the fluid is typically held about 0.9 m above the persons
Assuming you have a thermometer and a device to measure : assuming you have a thermometer and a device to measure the speed of sound in a gas explain how you can determine the
If the sliding container from b is placed in an environment : a container initially at 323 k is heated to a final temperature of 573 k. if the device contains a mixture of nitrogen
The four tires on the authors car are inflated to an : the four tires on the authors car are inflated to an absolute pressure of 2.8 x 105 pa. if the car has a mass of 1650

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd