Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
During the manufacturing process, a circular steel bar of diameter20mm and length of 1.2m is subjected to an axial load P. Themodulus of elasticity of steel is 207 GPa. The steel bar mustacquire an elastic strain energy of 14J. Find yield strengthfor a factor of safety of 3 with respect to plastic deformation.
a hydraulic jump is to be formed in a trapezoidal channel with a base width of 20ft and a side slope of 2:1. The upstream depth is 1.25ft and Q=1000 cfs. Find the downstream depth and the head loss in the jump.
A dispersed plug chemical reactor has an influent flow with concentration of 150 mg/L of A and a flow rate of 100 gal/min (380 L/min). The reaction is first order, The rate equation : - dC/dt = kC= -r , and the rate constant is 0.4 h^-1 .
The vertical velocity of the box at the time that it hits the surface is v= 5m/s. After impact the camera experiences an acceleration of a = -kx, where k is a constant and x is the compression of the packing material.
a wheel rolls to the right with an angular velocity of 2 rad/s while slowing down at a rate of 3 rad/s^2. knowing the wheel rolls without sliding and ignoring the effect of gravity determine the location on the wheel where the net acceleration is ..
A horizontal pre-stressing force of 500kN is applied to rectangler beam. the beam has a depth of 500mm and a width of 250mm. the force is applied at a distance of 80mm below the x-x axis.
A hollow circular, gray cast-iron pipe supports a red brass rod and weight W = 2 kips, as shown. The outside diameter of the pipe is d = 6". If the allowable compressive stress in the pipe is 5000 psi and the allowable shortening of the pipe is 0...
Conduct either a qualitative or quantitative risk assessment on this project. Identify the risk factors that you consider most important for the suspension bridge construction. How would you assess the riskiness of the project? Why?
If the toluene concentration in the water supply is 1,000 ppb, the treatment objective is 5 ppb, and the flow of water is 378 L/min (100 gpm), what mass of PAC must be placed in a contact basin on a daily basis to satisfy the treatment objective
Two control points A "station" (1000E, 1000N) and B "backsight" (594.22E, 877.68N) are available within the area. Indicate the procedure to satisfy the orientation and calculate the required total station reading towards B.
A 4.00-cm-diameter, 0.80-m long rod of aluminum 7075-T6 is subjected to an axial tensile force with a factor of safety of 1.75. The yield stress and modulus of elasticity of aluminum 7075-T6 are 500. MPa and 210. GPa, respectively.
a spot speed study was conducted on a freeway on which the mean speed and the standard deviation were found to be 72 .4 mi/hr and 5.4 mi/hr, respectively. what is the range of the values that would be expected to contain the middle 95 percent of s..
A simple beam has a 24 foot span and a W16 X 50 section. Determine the maximum flexural stress due to two concentrated loads, both 20 kips, at the 1/3 point and the 2/3 point (8 feet and 16 feet) on the beam.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd