Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
The 3 inductors in the circuit are connected across the terminals of a black box at t=0. The resulting voltage for t>0 is known as Vb. If i1(0) = 10 A and i2(0) = -5 A, find:
a) io(0)b) io(t), t>0c) i1(t), t>0d) i2(2), t>0e) What is the total energy delivered to the black box?f) What is the value of the internal resistance of the box?
To the right of the circuit is an 8H (i1) and a 32H (i2) inductor in parallel. Beneath that and to the right (running up to the parallel inductors is a 3.6 H Inductor (In series). To the right of that is a wire with a switch (T=0) with the other side of that wire attached to the far side of the parallel inductors. In parallel with that wire (to the far right) is the black box. On the box Vb = 1250e^(-25t)V
An NMOS pass-transistor switch with W/L= 1.2 um / 0.8 um. used in a 3.3-V system for which Vt0 = 0.8 V,(lambda)= 0.5 V^(1/2), 2(phi)f= 0.6 V , unCox = 3upCox = 75 uA/V^2, drives a 100-fF load capacitance at the input of a matched standard CMOS inv..
The motor driven by a switch-mode dc-dc converter, which has a bus voltage of 200V. The switching frequency fs = 25 kHz. Calculate and plot the waveforms for va(t), ea(t), ia(t), and id(t) under the following conditions
Discuss how the ethical problem solving techniques presented in this course could be applied to bribery and the acceptance of gifts. This discussion should be two paragraphs in length.
Three identical impedances of (12+j15)ohms are connected in wye to a 550V balanced three phase source. Determine, (a)the magnitude of the line currents. (b) the total power dissipated for the three phases. (c)the total reactive power. (d)the power..
Simulate the second-order RLC circuit using simpower Matlab simulink.This circuit has DC source voltage Vs=220V, Inductance L=2mH and Resistance R=160 ohms.Determine the capacitance values for each case
A single-phase 50-KVA, 2400/240-volt, 60-Hz distribution transformer has a 1-ohm equivalent leakage reactance and a 5000-ohm magnetizing reactance referred to the high-voltage side. If rated voltage is applied to the high-voltage winding
Draw the correct circuit to serve a 7.2kv single-phase load from a 2.4kv source. If the laod is 50kVa at pf=.8 lagging, compute the secondary and primary phasor currents. is this a step-up or step-down application
Block diagram and equations for control system water fill, Develop a control system to fill a container with water after it is emptied through a stopcock at the bottom
A modulating signal consists of two sinusoidal components: 1 kHz and 3 kHz. The transmitter carrier frequency is 80 kHz. Assume in a SSB-USB modulated signal that the inserted carrier at the receiver is 200 Hz too high.
Design a garage door controller using PLC Ladder Diagram (RSLOGIX 500 PLC SIMULATOR). The behavior of the garage door controller is as follows there is a single button in the garage, and a single button remote control.
Write an equation to help determine P-type body doping concentration Na for a required threshold voltage V (sub TN) for an N-channel Al-Sio(sub 2) -Si MOSFET. Use the equation to design an N-MOSFET with a thershold voltage of 10V
A boost converter has 5 V input and 12 V output at 60 W. The diode is ideal. The transistor requires 1 uS to turn on or off. The switching frequency is 100 kHz. The storage components are large.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd