Find what is the step response of the filter

Assignment Help Electrical Engineering
Reference no: EM13270037

Given the digital filter transfer function H(z)=1-z^-1 , what is the step response (that is, the input to the filter is unit step sequence u(n) ) of the filter? A. y(n)= delta(n)+delta(n+1) B. y(n)=u(n-1) C. y(n)=u(n)-u(n-1) D. y(n)=u(n-2)

Reference no: EM13270037

Questions Cloud

What is the expected output for an input voltage : A HCS12 ATD has been set-up to perform a right-justified, 10-bit, signed operation. What is the expected output for an input voltage of 3.09V The voltage range is 0-5V.5V/4096 = 4.88 mV.
Define the heat capacity of a system is defined as the ratio : The heat capacity of a system is defined as the ratio of the infinitesimal amount of heat absorbed to the corresponding increase in the temperature when some process is carried out. Show that the heat capacity at constant volume is C_V is equal to
Compute the current price of the bond : Compute the current price of the bond. (Do not round intermediate calculations. Round your final answer to 2 decimal places. Assume interest payments are annual.) Current price of the bond $.
Obtain the final temperature of the block : Consider a 10.0 kilogram block of copper, specific heat = 387 J/kg*C. The initial temperature of the copper is 25*C, obtain the final temperature of the block
Find what is the step response of the filter : Given the digital filter transfer function H(z)=1-z^-1 , what is the step response (that is, the input to the filter is unit step sequence u(n) ) of the filter A. y(n)= delta(n)+delta(n+1) B. y(n)=u(n-1) C. y(n)=u(n)-u(n-1) D. y(n)=u(n-2)
Explain the temperature of the sample in degrees celsius : If 6.830 moles of an ideal gas has a pressure of 3.290 × 105 Pa and a volume of 0.105 m3, what is the temperature of the sample in degrees celsius
Find the magnitude of the frictional force on the block : The right figure shows a force of magnitude F = 12.0 N applied to an 8.00 kg block at a downward angle of ? = 30.0°. find the magnitude of the frictional force on the block
Find the greater number in a memory location : Write an assembly language program to compare two 1 byte numbers and find the greater number in a memory location.
Find the tension in each half of the rod : Ball A is attached to one end of a rigid massless rod, while an identical ball B is attached to the center of the rod, Find the tension in each half of the rod

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Find the phase relation between the total voltage nd current

Then find the phase relation between the total voltage and current; is it leading or lagging when the frequency is below resonance and above resonance; what is the nature of the circuit in those two regions(capacitive or inductive).

  Find the value of the current i in terminal voltage changing

Consider a VBE multiplier with R1=R2= 1.2k ohms utilizing a transistor that has VBE= 0.6V at Ic = 1ma, and a very high beta. (b) Find the value of the current I that will result in the terminal voltage changing (from the terminal voltage 1.2-v val..

  Draw a suitable circuit that includes a resistor

Place the relay in the Collector circuit, the resistor in the Base circuit and the diode in parallel with the relay to provide a path for current due to energizing the relay.

  Develop a comparator circuit that goes high when temp rises

A sensor provides temperature data as 360 uV/C. Develop a comparator circuit that goes high when the temperature reaches 530 C

  Explain what is the purpose of the adc

Discuss the different analog-to-digital converter (ADC) types and configurations. What is the purpose of the ADC. How do you interface to the different configuration

  Write while loop that initally will blink an led1 once

Assume one LED (LED1) and one switch input (SW1). Write a while(1) { } loop that initally will blink an LED1 once power is applied. On each press OR release of SW1, alternate between terminating blinking and resumingine the blinking. Draw a state ..

  What would be the general form of a voltaqe v

Given a circuit with 10 resistors, a CCVS gix, two independent voltage sources v1 and v2, as well as an independent current source i1. What would be the general form of a voltaqe v across a specific resistor R

  How many booths should be operated to minimize total cost

Cars arrive at a toll plaza at the rate of 60 cars per hour. There are four booths, each capable of servicing 30 car per hour. Assume a Poisson distribution for arrivals and an exponential distribution for service time.

  Develop a system to help students learn morse code

Develop a system to help students learn Morse Code. The system will have one input and 26 outputs (one per letter). The user sends in Morse Code pulses on the input, and as characters are completed the appropriate letter is lit up momentarily.

  Find the output for the given input data

2) Draw the logic circuit for each of the following. For each gate, determine EVEN or ODD parity and find the  output for the given input data: a) 4-input XOR, input data=1001 b) 5-input XOR, input data-10010 c) 6-input XOR, input data=101001 d) 7-..

  Find input current and power factor at maximum torque

A 500 hp, three-phase, 2200 V, 60 HZ, 12-pole, Y-connected, wound-rotor induction motor has the following parameters: R1 = .225 ohm : R'2= .235 ohm Xeq = 1.43 ohm and Xm = 31.8 ohm and Rm = 780 ohm

  Does given arrangement violate osha standards

A painter is standing on a work platform that is 27 feet above ground level. For fall protection, the worker's safety harness D-ring is attached to a 12-foot shock absorbing lanyard that is securely fastened to the structure at a point 40 feet abo..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd