Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
a) What is the voltage across a 220ohm resistor if the current through it is 5.6 mA?b) What is the current through a 6.8ohm resistor if the voltage drop across it is 24 V?c) What is the power delivered by a 6 V battery if the current drain is 750mA?d) The current through a 4 k? resistor is 7.2 mA. What is the power delivered to the resistor?
DESIGN A mod 6 counter that counts in the natural sequence.DO NOT include the undesired states in your design (therefore, you will have don't care condition ). show all steps for the complete design of this synchronous counter
A three-phase, 60 Hz, six pole, wound rotor induction motor draws 10kw when driving its normal load. It draws 700 W when the load is diconnected. The rotor and stator copper losses under normal load are 295 W and 310 W respectively.
The relative dielectric constant of the printed circuit board (PCB) is 4 and the microstrip lines have a characteristic impedance of 80W. The length of the microstrip lines are 30mm and 45mm, respectively.
The detector will take in numbers from 1510 to 010 encoded in binary labeled [N3:N0] with N3 being the most significant bit. The output will be asserted when the decimal value of the input is a prime number (i.e., 2,3,5,7,11,13). The output is de-..
Rated voltage is applied to the low voltage winding and the high voltage winding is open-circuited. Under this condition, the current into the low voltage winding is 2.4 A, and the power taken from the 2400 V source is 3456 W.
Design a 3 th order high - pass Butterworth filter with a High Frequency gain of 20 DB and a cutoff frequency of 20 rad/s. 2) Using MATLAB, plot the frequency respon se of this filter, and the location of the filter poles.
An analog AMPS cell phone channel at 900MHz carrier has a carrier amplitude of 4V and is a modulation signal m(t)=Bmsin(10000*pi*t). The amplitude of the modulating signal is 2V and the peak frequency deviation was found to be 10kHz
A control system is needed to control a small shopping center parking lot lighting system and the exterior lighting for the building. The design specifications require that the parking lot lighting and the exterior lighting turn on at dusk automat..
Characteristics of a filter, A filter has the following characteristics: Attenuation = 3.0 dB from 0 Hz to 2 kHz. From 2 kHz to 20 kHz attenuation increases from 3 dB to 23 dB in a straight line when plotted on axes of power in decibels (vertical a..
Write an asm HCS12 program to flash LEDs on a dragon+ board three times when SW5 is pressed with a 5 kHz frequency, and 50% duty cycle clock signal. Generate a clock signal with 5 kHz frequency, and 50% duty cycle.
Help with problem in Control signal processing class, Consider the unity-feedback control system whose open-loop transfer function is
The continuous-time sinusoid x(t) = cos(300?t) is sampled every Ts = 2.0 ms, so that x[n] = x(0.002n) For what other values of f in the range 0 Hz to 2.0 KHz does the sinusoid v(t)
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd