Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
John's friend Sven has an "automatic crossover" power supply that can output up to 50V and up to 12Amps. What is the output voltage and current of the supply when John connects a 3O resistor to Sven's supply, when he has set all control knobs to their maximum levels?
The received power at a receiver antenna is -38 dBm. If the system impedance is 50 Ohms, what is the voltage at the receiver antenna. What is the total average power for a commercial AM transmitter with an unmodulated carrier power of 20 kW and 100%..
Refer to the Wheatstone Bridge diagram. If R1=1ohm, R2=111ohm, Runknown= 1ohm, R3 is set at 1Kohm, and the battery is 9V:What is the current flowing through the galvanometerohm Use 60ohm for the internal galvanometer resistance in calculations.
1. An AM signal has an unmodulated carrier voltage VC = 10VP, a load resistance of RL = 10, and a modulation index of m = 1. 2. You are tuned to an AM station at 1200 KHz. Write down the frequency components of the received AM signal.
Once the voltage across the load reaches 5V the load will no longer act as an open circuit and the capacitor will discharge. Once the load voltage has droped to 0.2 the load will act as an open circuit and the capactior will begin to charge once ..
a)What is the voltage across a 220? resistor if the current through it is 5.6 mA b)What is the current through a 6.8? resistor if the voltage drop across it is 24 V c) What is the power delivered by a 6 V battery if the current drain is 750mA
A transducer produces a sinusoidal waveform with an amplitude of 2.5 VPK and a DC offset of 0 VDC. The ADC input signal range is 0 V to 5 V. Describe the signal conditioning circuit that is needed to use the full-scale range of the ADC.
An emitter follower is operating at a collector bias current of 0.25 mA and is used to connect a 10 kiloohm source to a 1 kiloohm load. If the nominal value of beta is 100, what output resistance Rout and overall voltage gain G result
Write the formula for the maximum clock frequency for an n-bit synchronous parallel binary counter. Beyond what value of n is your formula no longer valid. let Ttq denote the propagatoin delay from T to Q in a T flip-flop.
A CT signal x(t) can be depicted as follow. It is a periodic function with T0 = 1 micro sec, and amplitude A = 1. The second signal y(t) is a sinusoid function with the fundamental frequency of 900 MHz, i.e., y(t) = cos(2*pi*fc*t)
A three phase synchronous generator operates onto a grid bus of voltage 33 kv (line to line). The armature reactance of the machine is 2 ohms per phase and the leakage reactance is 3 ohms per phase.
The voltage between two charged parallel plates is 5 volts (the top plate has more negative potential). What energy is acquired by an electron that is moved from the bottom plate up to the top plate
A collimated light beam from a helium-neon laser at 632.8 nm wavelength impinges on a dielectric film of refractive index of 2.0 at an angle of 75 degrees to normal, with a polarization at 45 degrees to the plane of incidence.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd