Find what is the hydrostatic pressure force on the hatch

Assignment Help Civil Engineering
Reference no: EM13322787

A circular hatch, 2-m in diameter has its top 10-feet under water ( fresh water s.g = 1.0), and is oriented vertically in the water column. What is the hydrostatic pressure force on the hatch, in Newtons.

Reference no: EM13322787

Questions Cloud

Why is the formulation of the rto and rpo : Why is the formulation of the RTO and RPO a trade-off process?
Find the phase angle between the current and applied voltage : n LRC circuit consists of a 291 Ohm resistor, a 30 micro Farad capacitor, and a 276 mH inductor, find the phase angle between the current and the applied voltage
Calculate the force that the bolt must put on the hatch : A circular hatch, 2-m in diameter has its top 10-feet under water ( fresh water s.g. = 1.0), and is hinged on the bottom, and held closed on the top with a single bolt. Perform a moment balance about the hinge
Critique website that is different to rest of our friends : Web devolving assignment - Critique a website that is different to the rest of our friends-classmates.
Find what is the hydrostatic pressure force on the hatch : A circular hatch, 2-m in diameter has its top 10-feet under water ( fresh water s.g = 1.0), and is oriented vertically in the water column. What is the hydrostatic pressure force on the hatch, in Newtons.
Calculate the max current in the circuit : In a series LRC AC circuit, the resistance is 19 Ohm, the inductance is 21 mH, and the capacitance is 14 micro Farads. Calculate the max current in the circuit
Determine the stress in the wall at two points a and b : The end caps are spherical. The cylinder has length of 30 inc., a diameter of 8 in., and a wall thickness of 0.125 in. Determine the stress in the wall at two points A and B. For each, draw the stresses on a 3-D element.
Depict the structural formula of 3,4-diethyl-3-hexene : Draw the structural formula of 3,4-diethyl-3-hexene. If more than one isomer of this compound exists, then both isomers must be drawn
What stress on the structure will lead to the failure : A structure is designed with a factor of safety of 5.25 psi. If the allowable stress of the structure is 3000 psi. What stress on the structure will lead to its failure

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculate the retardation coefficient for the three chemical

Groundwater has been contaminated with three chemicals: benzene (log Kow 2.13), pentachlorobenzene (log Kow 5.03), and naphthalene (log Kow 3.36). The aquifer (rs = 2.3 g/cm3; h = 0.4; foc = 0.02) has a gradient of 0.004 and hydraulic conductivity..

  Determine the maximum design shear force for the loading

A simply supported span of 28 feet must carry a uniform loading that produces a total factored maximum moment of 300 K-ft including the beam weight. The concrete can be 3.5 ksi and the steel is grade 60.

  What is the min possible value for the pressure difference

Part of a vertical piping system consists of 8 ft of 4 in diameter, connected to 8 ft of 3 in diameter above, and connected to 8 ft of 2 in diameter above that. Water at 60 F flows up the pipe (no downward flow occurs).

  Determine speed of sliding on smooth plane just after impact

If they are sliding on a smooth horizontal plane with the velocities shown, determine their speeds just after impact. The coefficient of restitution between them is e = 0.6. Disks A and B have a mass of 16kg and 11kg , respectively.

  Determine x and z components of force required to hold

The stream hts a stationary splitter, such that half of the flow is diverted upward at 45o. and the other half is directed downward, and both streams have a final speed of 18ft/s.

  Determine magnitude of velocity and acceleration of particle

The motion of a particle on the surface of a right circular cylinder is defined by the relations, R = A, theta = 2pi(t), and z=Bsin(2pi)(nt), where A is a constant. Determine the magnitudes of the velocity and acceleration of the particle at any t..

  Is inventor claim valid to have an invented adiabatic flow

An inventor claims to have invented an adiabatic steady-flow device with a single inlet-outlet that produces 100 kW when expanding 1 kg/s of air from 900 kPa and 300 degrees C to 100 kPa.

  Determine the produce of inertia for the shaded area

Determine the produce of Inertia, Ixy, for the shaded area to the right using integration. Use the parallel axis theorem to find Ibarxy, the product of inertia with respect to the centroidal axes.

  Determine the normal depth-critical depth and velocity

A PVC pipe with a diameter of 30 inches will carry a flow of 20 cfs. the bottom slope is 0.005 and the roughness coefficient is 0.015. determine the normal depth, critical depth, velocity and the froude number.

  Determining pressure in a coal mining dragline

The total flow then moves to a point W on the traction drive two metres off the ground, and travels through a nine millimetre diameter conduit. Ignoring all friction and minor losses, determine the pressures at points H and W.

  How is the minimum radius affected if the b decreases

Roller coasters are designed so that the riders will not experience more than a certain level of g-force during the ride. (The rider would experience B g's if hte normal force were Bmg where B is a numbe

  What is the present worth of the road at an interest rate

The cost of extending a certain road is $850,000. Resurfacing and other maintenance are expected to cost $175,000 every 3 years and lasts for 96 years. What is the present worth of the road at an interest rate of 6% per year (over that period)

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd