Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A Direct Sequence Spread Spectrum system receives a 100 Mbps digital signal at its input and transmits a spread signal at 800 Mbps. The received spread signal has an SNR of -3dB.
1. What is the Gain of that system?
2. Write down any chip of your own that satisfies the condition stated above.
3. For the data bit stream 0 0 1 1 0 0 1 0 0 1, what is the corresponding spread bit stream, using your chosen chip above?
5. Consider a 4 channel CDM system with the following CHIPS: A: -1 -1 -1 1 B: -1 -1 1 -1 C: -1 1 -1 -1 D: -1 1 1 1 a) Show that each one of those chips is orthogonal to all of the others. b) If the CDM signal 1 -1 -3 1 is received, by all receivers, what will be the conclusion of each one?
Three screws are drawn at random from a lot of 100 screws, 10 of which are defective. Find the probability that the screws drawn will be nondefective in drawing (a) with replacement, (b) without replacement.
The R2= 6 homs load in the circuit is absorbing four times as much average power as the R1 = 20 ohmsohms load. The two loads are matched to the sinusoidal source that has an internal impedance of 500 (angle) 0 1)What is the numerical value of a1
pressure limits of 10 kPa and 8 MPa, with reheat occurring at 4 MPa. The temperature of steam at the inlets of both turbines is 500°C, and the enthalpy of steam is 3185 kJ/kg at the exit of the high-pressure turbine
In order to control the slope of a ramp produced by an integrator, the values of Vin, R, and C may be varied. Assuming a fixed value for C of 10 μF, would it be better to have a relative large Vin with a correspondingly large value of R
To understand dierent signal models To be able to model a discrete-time system and design simple signal processing algorithms.
If we use the PC-relative addressing mode, and want to allow control transfer between instructions up to 50 locations away, how many bits of a branch instruction are needed to specify the PC-relative offset
A parallel plate capacitor has gasoline as the dielectric. The area of the plate is 0.25 m^2 and the distance between two plates is 5cm. a. Find the capacitance given that the relative permittivity of gasoline is 2.
A pn junction diode is forward biased by a Thevenin circuit consisting of Rth = 5kohm and Vth = 10sinwt where w= 2pi*10rads/s. Find the diode voltage and current as functions of time.
a positive-sequence shunt admittance y= j4.4* 10-6 S/km. for this line if it has 70% shunt reactive (inductors) compensation and 40% series capacitive compensation. Half of this compensation is installed at each end of the line.
Discuss the sequence of actions that occur in the operation of the control system for a traffic light that includes sensors in the roadbed. Indicate which actions are time-driven and which actions are event-driven.
Assume that you have two DC voltage sources of 1.5 volts each (like two AA batteries). The positive terminals are wired together (joined together) and the negative terminals are labeled A and B respectively.
With the 1s complement scheme, how does the receiver detect errors? Is it possible that a one bit error will go undetected? How about a two bit error?
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd