Find what is the average current drain from the battery

Assignment Help Electrical Engineering
Reference no: EM13285945

Suppose that we are designing a cardiac pacemaker circuit. The circuit is required to deliver pulses of 1-ms duration to the heart, which can be modeled as a 500 ohm resistance. The peak amplitude of the pulses is required to be 5 V. However, the battery delivers only 2.5 V. Therefore, we decide to charge two equal-value capacitors in parallel form from the 2.5 V battery and then switch the capacitors in series with the heart during the 1-ms pulse. What is the minimum value of the capacitances required so the output pulse amplitude remains between 4.9 V and 5 V throughout its 1-ms duration? If the pulses occur once every second, what is the average current drain from the battery? Use approximate calculations, assuming constant current during the output pulse. Find the ampere-hour rating of the battery so it lasts for five years.

Reference no: EM13285945

Questions Cloud

Determine the distance between the spheres : Two metal spheres are separated by a distance of 0.8 cm and a power supply maintains a constant potential difference of 850 V, what is the distance between the spheres at this time in nm
How an annuity can be used in someone financial portfolio : Suggest a real-life example of how an annuity can be used in someone's financial portfolio to balance their investments.
What are the magnitude and angle of the overall displacement : An ant, crazed by the sun on a hot Texas afternoon, darts over an xy plane scratched in the dirt. What are the magnitude and angle (relative to the positive x axis) of the overall displacement
Explain the reaction occurs and equilibrium : A mixture initially contains and in the following concentrations: a= 0.700M , b= 1.25M , and C= 0.550M . The following reaction occurs and equilibrium is established
Find what is the average current drain from the battery : Suppose that we are designing a cardiac pacemaker circuit. The circuit is required to deliver pulses of 1-ms duration to the heart, which can be modeled as a 500 ohm resistance. The peak amplitude of the pulses is required to be 5 V.
Find the magnitude of the cars total displacement : A car is driven east for a distance of 49 km, then north for 23 km, and then in a direction 28° east of north for 28 km. FIND the magnitude (in km) of the car's total displacement from its starting point
Calculate the approximate power factor of the ge profile : The commercial version of the GE Profile Advantium oven operates at 240V, draws 30.0 amps, and outputs 0.95 kW. Calculate the approximate power factor
Define condensed isothermally and reversibly to liquid water : An amount of H2O vapor (gas) is condensed isothermally and reversibly to liquid water at 100ºC where it occupied a volume of 838 cm3. The standard enthalpy of vaporization of water at 100ºC is 40.66 kJ mol-1, the density of liquid water at 100ºC i..
What is the final charge on each object : Four identical metallic objects carry the following charges: +8.2 µC, +7.0 µC, -2.6 µC, and -9.2 µC. What is the final charge on each object

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What frequency components will be obtained at the output

Given a sawtooth signal with fundamental frequency = 20 KHz as the input signal going into an ideal Highpass Filter with cutoff frequency fc = 60 KHz, what frequency components will be obtained at the output

  Identify the element for the voltage and total current

A capacitance C=35 uF is in parallel with a certain element. Identify the element, given that the voltage and total current are v=150sin3000t(V) and i of tau=16.5sin3000t+72.4 degrees (A)

  How long can printed circuit traces before being considered

For a 32 bit CMOS 5 volt microprocessor that has a 32 bit address bus and a separate 32 bit data bus, and the processor has a 1 nS rise time and 0.5 nH of ground inductance on a board made from glass epoxy material.

  Draw block diagram of a communication channel

Explain the characteristics of electromagnetic waves and application to communications systems and determine the signal spectra for the content of complex waveforms

  Find new corrected power factor after installing shunt capa

A 2.4KV, single-phase circuit suppllies a load of 250KW at a lagging power factor, and the load current is 160A. If it is necessary to improve the power factor, determine the following: (a)The uncorrected poer factor and reactive load.

  Give the impulse responses of lti systems

Impulse Responses of LTI systems can be physically found by inputting \(x[n] = \delta[n]\)to the system and measuring the output. Assume that during the process, we inadvertently input\(x[n] = \delta[n] + \delta[n-1]\)

  What is the change in voltage from a voltage range

A certain sine wave has a frequecny of 2.2kHz and an rms value of 25 V. Assuming a given cycle begins (zero crossing) at t=o s, what is the change in voltage from 0.12 ms to 0.20 ms

  Find the frequencies of the poles fp1 and fp2

A CG amplifier is specified to have Cgs=2pF, Cgd=0.1 pF, CL=2 pF, gm=4 mA/V, Rsig = 1k-ohm, and R'L = 20 k-ohm. Neglecting the effects of ro, find the low-frequency gain vo/vsig, the frequencies of the poles fP1 and fP2

  Calculate the unknown constant in homogeneous part

b) find nonhomogeneous solution with method of undetermined coefficient with constants evaluated c) combine homogeneous soluton with nonhomogeneous solution to form the general solution calculate the unknown constant in homogeneous part

  Determin the total line current drawn from the supply

A 415V 50 Hz three phase supply has been divided into three balanced loads, as follows: LOAD 1 (STAR): 15 kVA at a power factor of 0.60 lagging; LOAD 2 (DELTA): 24 kW at a power factor of 0.55 lagging;

  Find the amount of fuel required per day and per 30 days

a combined -cycle, natural gas fueled power plant rated at 250 MWe has an efficiency of 65%. find the amount of fuel required per day and per 30 days.

  Determine the central line and control limits of the chart

it is required to establisg a chart for count of nonconformities for a manufacturing process. if 25 units are to be inspected and the total number of the count of nonconformities from all the units is 141, determine the central line and control li..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd