Find what combinations of loads produce the max shear

Assignment Help Civil Engineering
Reference no: EM13310155

beam is fixed at one end, spans 21' then goes over a roller support then 6' continues to hang over. there is a point load halfway betwen the supports (10.5') and another at the far end. there is also a distributed load that stretches the entire beam. each point load and distributed load is broken down into part live and part dead load. i need to find out the best way to solve for max shear and moment in the beam but i also need to find what combinations of loads produce the max shear and moment. only live loads can be "turned on or off'

Reference no: EM13310155

Questions Cloud

What are major characteristics of modern multimedia system : What are the major characteristics of a modern multimedia system? What is the most important characteristic in your opinion?
Find relation between reflection nd transmission coefficient : What is the relation between reflection and transmission coeffients of a sea wall
How many panels would you need : Geothermal heat is having another "revival". Explain how it works in a home and how much it would cost to add this to your home (determine your square footage or use an average 2000 square foot home), How many panels (size?) would you need
Explain possible isomers are there of an octahedral complex : How many possible isomers are there of an octahedral complex having the formula M(ABC)(NH3)(H2O)Br where ABC is the tridentate ligand H2N-C2H4-PH-C2H4-AsH2
Find what combinations of loads produce the max shear : beam is fixed at one end, spans 21' then goes over a roller support then 6' continues to hang over. there is a point load halfway betwen the supports (10.5') and another at the far end. there is also a distributed load that stretches the entire be..
How much work must be done on the hoop to stop it : A 110 kg hoop rolls along a horizontal floor so that its center of mass has a speed of 0.0760 m/s
What was the temperature of the copper : A copper ball of mass 150 g is removed from Bunsen burner flame and dropped into 500g of water at -20 %u030AC. what was the temperature of the copper when it left the flame
Determine how many grams of co2 are dissolved in the water : Four liters of water are equilibrated with a gas mixture containing carbon dioxide at a partial pressure of 0.3 atm. Henry's law constant for H2CO3* solubility is 2.0g/L-atm.
What is the carnot efficiency of a heat engine : What is the Carnot efficiency of a heat engine operating between the temperatures of 300 degrees C (573 K) and 100 degrees C (373 K)

Reviews

Write a Review

Civil Engineering Questions & Answers

  Do the first three time increments by hand

A variable-order reaction A-->B has the following rate expression: R(a) = -kC(a)/(K+C(a)) where k = 5mg/L-hr and K=40mg/L The reaction is to take place in a batch reactor. The initial concentration is 450 mg/L

  Determine the angle that vo forms with vertical by rocket

If the rocket's decent parachute does not deploy and the rocket lands 340 ft from A, determine the angle (alpha) that vo forms with the vertical, the maximum height h reached by the rocket, and the duration of the flight.

  How to compute the normal depth of a trapezoidal channel

A trapezoidal channel with a bottom width of 4 feet and side slopes 2:1 (H:V) and a bed slope of 1 percent conveys a discharge of 50,000 gpm. Assume n = 0.025. Compute the normal depth.

  Calculate the presence worth over a 5 year period

The cost for maufacturing a component used in intelligent interface converters was $23000 the first year. The company expects the cost to increase by 2% each year. Calculate the presence worth over a 5 year period at an interest rate of 10% per ye..

  Establishing a horizontal distance

A tape is calibrated and found to measure 100.04ft between the 0- and 100-ft marks. What measurements should be laid out to establish a horizontal distance of 682.25ft?

  Determine what is the max length of the slotted region

a rectangular bar of length l has a slot in the middle half of its length. the bar has width b, thickness t, and modulus of elasticity E. the slot has a width b/4. the stress in the middle region is 24000 psi, the length is 30 in, andthe modulus o..

  Determine the heat transfer and the work for the process

A cylinder fitted with a piston has a volume of 2ft^3 and contains 0.5 lbm of steam at 60 psia. Heat is tranferred to the stream until the temperatureis 500 F, while the pressure remains constant

  At what flow rate should the farmer pump the water

A farmer wants to irrigate a piece of land in 15 hrs. The area of the field is 15 acres. the farmer grows alfalfa that requires 3.5 inches of water during the 15 hours.At what flow rate should the farmer pump the water

  How much effort force is required to travel up

if a person and a wheelchair weigh 185 lbs how much effort force is required to travel up a ramp whose slope of 24.08 ft.

  Determine magnitude of rockets velocity and acceleration

When a rocket reaches an altitude of 40 m it begins to travel along the parabolic path (y-40)^2=160x, where the coordinates are measured in meters. If the component of velocity in the vertical direction is constant at Vy=180m/s

  Calculate the temperature of the air in fahrenheit

The "sea-level adjusted" pressure at the airport was about 30.57 inches of mercury. Assuming the density of air is 1.30 kg/m3 and the gas constant for air is 287. J/(kg K), calculate the temperature of the air in Fahrenheit.

  What is max mole fraction of methanol that can be achieved

A solution containing 30% methanol (by mol) is flashed to 1 bar, 70.82°C. Determine the phase of the system; if 2 phases, report the compositions and relative amounts of each phase.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd