Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A random sample of 50 suspension helmets used by motorcycle riders and automobile race- car drivers was subjected to an impact test, and on 18 of these helmets some damage was observed.
(a) Test the hypothesis, H0: p = 0.3 versus H1: p > 0.3 with a = 0.05.
(b) Find the P-value for this test.
(c) Find a 95% two-sided traditional CI on the proportion of helmets of this type that would show damage from this test. Explain how this confidence interval can be used to test the hypothesis in part (a).
(d) Using the point estimate of p obtained from the preliminary sample of 50 helmets, how many helmets must be tested to be 95% confident that the error in estimating the true value of p is less than 0.02?
(e) How large must the sample be if we wish to be at least 95% confident that the error in estimating p is less than 0.02, regardless of the true value of p?
A rectangular blade weighing 0.02 lbf is kept in the surface of water (sigma=0.073 N/m) solely by surface tension forces. What is the minimum perimeter of that the blade must have so that this is possible
What is the equivalency factor for the 14 kip single axle?
Use the Muskingum method to route a flood through a reach a river. The base flow is 100 cfs, and the incoming flood flow increases 50 cfs every 2 hr over a 6 hr period and the subsides at the same rate.
A small house is built in the arctic. It has four square walls of 500 ft2 each. For simplicity, we will assume it has no windows, and we are only interested in calculation the heat loss through the four walls. A total of one hundred Watts (100 kW)..
Our ESP is collecting 95% of the particles in our exhaust stream. We are under pressure to improve its performance. It has been suggested that if we were to cool the inlet gas from the present 600°F to 250°F
A jet aircraft is flying in a standard atmosphere at an altitude of 4,000 m at 900 km/hr. The frontal intake area of the jet engine is 0.80 m2. The engine exhaust area is 0.56 m2. The temperature of the exhaust gas is 120°C.
The initial waste concentration is 200 mg/l and the following constants have been determined: Ks=50 mg/l; k=5.0 days^-1; kd=0.06 days^-1; Y=0.60 Determine the minimum mean cell residence time, the mean cell residence time you would set for design.
Air is compressed from an initial state of 100 kpa and 170 *C to a final state of 600 kpa and 57 *c. Determine the entropy change of air during the compression process by using a) property values from the air table and b) average specific heats
A $78,000 invtestment in machinery is proposed. It is anticipated that this investment will cause a reduction in net annual operating disbursements fo $16,300 a year for 12 years. The investement will be depreciated for income tax purposes
Compute the maximum acceptable service load on an A36 steel plate tension member 1/4in.x12in. having a single line of holes parallel to the direction of loading. The load is 25% dead load and 75% live load, and 7/8in. diameter bolts are used.
A well with a radius of 0.5 m pumps at a constant rate of 1240 m3/day. After the cone of depression has achieved equilibrium, the piezometric heads at two observation wells 40 and 95 m from the pumping well are measured as 78.9 and 83.4 above sea ..
All stormwater will drain as sheet flow to the center, flow into a drop inlet, and travel through a pipe system to the nearest stream. The parking lot will be mowed grass (clay soil) with a slope of 2 percent toward the center.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd