Find the voltage across the 20-ohm resistor initially

Assignment Help Electrical Engineering
Reference no: EM13262509

A coil of 10H inductance and 5Ω resistance is connected in parallel with a 20Ω resistor across a 100-V DC supply which is suddenly disconnected.
Find The voltage across the 20Ω resistor initially and after 0.3 sec.

Reference no: EM13262509

Questions Cloud

What is the value of the total circuit complex impedence : An input signal of 10V at 0 degrees is applied to a series RLC circuit with resistore R=100 ohm, inductor L=40 mH, and capacitor C = 0.5uF. determine what is The value of the total circuit complex impedence.
How many barrels of crude 1 should be purified : Before blending the crude oil into gas, any amount of each crude can be "purified" at a cost of $3.50 per barrel. This purification eliminates half of the impurities in the crude oil.
Define why the melting point of 4-bromonitrobenzene : Explain why the melting point of 4-bromonitrobenzene is considerably higher than that of the 2-isomer
What is mullineauxs wacc : Mullineaux Corporation has a target capital structure of 70 percent common stock, 10 percent preferred stock, and 20 percent debt. Its cost of equity is 12 percent, the cost of preferred stock is 6 percent, and the pretax cost of debt is 8 percent..
Find the voltage across the 20-ohm resistor initially : A coil of 10H inductance and 5Ω resistance is connected in parallel with a 20Ω resistor across a 100-V DC supply which is suddenly disconnected. Find The voltage across the 20Ω resistor initially and after 0.3 sec.
Why might prices not be strong form effcient : Why might prices not be strong form effcient? List two reasons and briefly describe.
Are there other factor neith or fifty three percent of the : Suppose we analyzed the effect of grade point averages on grades in a specific class and found the results to have an R-aquared value of 0.53. What do we know? Are there other factor, neith or fifty three percent of the variability?
Generate k-map row and column headings for arbitrary number : Write a C-program to generate K-map row and column headings for an arbitrary number of row or column input variables, i.e. 4x4 k-map for 2 row and 2 column variables, 16x16 k-map for 4 row and 4 column variables, etc.
What you can infer from the company success : One year ahead of the planned IPO the company is already raising capital through private placement markets. What you can infer from the company success in the private market about the success of the IPO?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What is the rate of acceleration produced by photon momentum

The intensity of solar radiation is 1366.1 W/m2 in space. This light strikes a 10 m2 solar panel of a satellite. Assuming that all the light is absorbed, how much force (momentum per second) is transferred

  What force f is required by the operator

The floor causes couple moments Ma =60 Nm and Mb =35 Nm on the brushes of the polishing machine. What force F is required by the operator so that the resultantmoment on the polisher is zero. Set a = .3 m.

  What is the dynamic range for an 8-bit adc

1) What is the dynamic range for an 8-bit ADC 2) A device that responds to a small current or voltage change by activating a mechanical switch allowing a larger amount of current flow is a: a) transistor. b) transducer. c) solenoid. d) relay.

  What is the step response equation for charge time

1. What is the step response equation for charge time 2. How to determine the current in RLC circuit using the osciscope 3. List three reseasons why the measured value and pspice value for tau are different.

  Design a dc power supply that provides a nominal dc voltage

Design a dc power supply that provides a nominal dc voltage of 12V that will supply a load current of up to 30mA. Use a Bridge rectifier in your design and isolate your circuit by use of a transformer at the input.

  Determine norton current and source resistance

A particular signal source produces an output of 30 mV when loaded by a 100-k ohm resistor and 10 mV when loaded by a 10-k ohm resistor. calculate the thevenin voltage, Norton current, and source resistance.

  Define a shunt regulator utilizes a zener diode

A shunt regulator utilizes a zener diode whose voltage is 5.1V at a current of 50 ma and whose incremental resistance is 8 ohms. The diode is fed from a supply of 12 V nominal voltage through a 220 ohm resistor

  What are the corresponding voltage-current and power gains

A buffer amplifier with a gain of 1 V/V has an input resistance of 1M and an output resistance of 10 ohm. It is connected between a 1-V, 100-k ohm source and a 100-ohm load. What load voltage results and what are the corresponding voltage, current,..

  What is the maximun temperature that the device may operate

A GaAs device is dopeed with a donor concentration of 3*10^15 cm^-3, For the device to operate properly, the intrinsic carrier cconcentration must remain less than 5 percent of the total electron concentration.

  Draw the logic diagram for the four-bit circuit

Draw the logic diagram for the 4-bit circuit, using full adders and multiplexers. Determine the arithmetic operation performed for each of the four combinations of S and Cin: 00, 01, 10, and 11.

  How many turns are required for a circular loop

How many turns are required for a circular loop of 100-mm radius to develop a peak emf of 10mV if the loop rotates 30r/s in the earth's magnetic field Take B = 60E-6T.

  Explain method to display the information of the rectangle

Design and implement a Rectangle class. Make your class inherit from the Point class given in the lecture (notice that a rectangle can be described through the upper-left vertex, the height, and the width).

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd