Find the value of the force on q1 and q2

Assignment Help Electrical Engineering
Reference no: EM13251277

Two point charges, Q1 =30 C and Q2 =-100 C,are located at (2,0,5) m and (-1,0,-2) m, respectively. Find the force on Q1 and Q2.

Reference no: EM13251277

Questions Cloud

Explain and balance the redox reaction in basic solution : Balance the following redox reaction in basic solution. Which of the following statements is not correct? Cr3+(aq) + ClO3-(aq) + OH-(aq) ? Cl-(aq) + CrO4^2-(aq)
Explain what was the original pressure of hi : The final volume of the balloon is 1500 mL. The atmospheric pressure is 1.00 atm. What was the original pressure of HI in the cylinder before the release of HI
What is the relationship between ic and il at is minimum : (1) Explain what happens in a series circuit when the frequency makes Xc equal to XL. Does it have a name (2) What is the relationship between Ic and IL at Is minimum (3) Why is the source current, Is, minimum at certain frequency
What is the value of the magnetic field created : A solenoid is 15 cm long and has 9000 turns. The current through the solenoid is 6A. What is the value of the magnetic field created
Find the value of the force on q1 and q2 : Two point charges, Q1 =30 C and Q2 =-100 C,are located at (2,0,5) m and (-1,0,-2) m, respectively. Find the force on Q1 and Q2.
Explain iron will act as the stronger oxidant : Aluminum will act as the stronger reducing agent and iron will act as the stronger oxidant. In the spontaneous reaction, the oxidation number of iron will increase.
Explain how much of the pressure will be due to hydrogen : 7. 0.500 g each of hydrogen, H2, and carbon monoxide, CO, are introduced into an evacuated 250. mL flask. What will be the total pressure (in atm) in the flask at 22ºC? How much of the pressure will be due to hydrogen
Find the angle of deviation for the emerging beam : Light is incident on a thin prism for which n= 1.5. Find the angle of deviation for the emerging beam
Determine what is the terminating load impedance : Use Smith Chart: A 100 Ohm air-coaxial transmission line is measured to have an input impedance of 100 + j100 Ohms. If the system is operated at 100 MHz and is one meter long, what is the terminating load impedance

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Find group delay between the highest modes

Parallel plate waveguide has plate seperation of 2cm, filled with dielectric material with an index refration of n=3, lenght of wavelengh guide z=50m opertaing at 10 Ghz. a) find the cutoff frequency

  Explain autocorrelation and tao

Autocorrelation and Tao, question from my ECE 302 class regarding the mean of a random process given a particular autocorrelation function in terms of tao.

  Identify the output samples influenced by boundary effects

The frequencies of the tones are 100 Hz, 300 Hz, and 450 Hz. The sampling rate is 1 kHz. Describe a low pass, a band pass, and a high pass filter that could be used to detect the individual tones.

  Determine power series values

Determine power series values for common scientific and engineering functions and Obtain the Maclaurin series for the following functions. State the values of the x which the series converge.

  Explain transformer having a single secondary winding

A full-wave bridge rectifier circuit with a 1-kohms load operates from a 120-V (rms) 60-Hz household supply through a 10-to-1 step-down transformer having a single secondary winding

  Calculate the total i2r resistance loss and efficiency

A 1,000 kVA, 3,200V, single phase 60Hz, 24 pole alternator/generator has an stator winding re-sistance of 0.1 ohm from line-to-neutral. The rotor is not a permanent magnet but a separately pow-ered electromagnet (field windings)

  What are measured values for the two resistances

What do you believe would happen, if you removed the 220 ohm resistor from the circuit and connected the LED directly to the 555 integrated circuit. Are there any appreciable differences between labeled, calculated.

  Determine speed of the motor and motor torque

The speed of a 10HP, 230V, 1200 rpm separately excited DC motor is controlled by a 1-phase full-wave bridge converter. The rated armature current of the motor is 10 A. The armature resistance is 0.25 Ohm and the armature inductance is 10 mH.

  What is the mean number of transmissions required

If a frame is damaged then in this network the receiver sends back a request for retransmission. (For simplicity, assume all these requests arrive back perfectly at the sender). What is the mean number of transmissions required to successfully tra..

  Examine of link budget dth qpsk satellite link

Analysis of link budget DTH QPSK Satellite link, A direct-to-home satellite television system uses a geostationary satellite in orbit above the equator at a longitude of 109 degrees west.

  Explain bisection-false position and newton raphson methods

You deposit 10% of your annual salary at the each of each year in a retirement account. F= Future worth A1= first annual deposit n=number of years g=geometric gradient F=A1(1-(1+g)^n(1+i)^-n/(i-g))(1+i)^n use Matlab to graph the function.

  Determine the hv-side fuses needed to protect

Determine the HV-side fuses needed to protect a 3x140kVA, 12470/208 YNyn0 distribution transformer bank. Show and explain step by step the procedure you employ to solve this question. Use the type K and type T fuse curves

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd