User Account

All Pages

Find the value of land c at resonance

Assignment Help Electrical Engineering
Reference no: EM13249309

The cutoff frequencies of a series resonant circuit are 5400 Hz and 6000 Hz.

a. Find the bandwidth of the circuit.

b. If Qs is 9.5, find the resonant frequency of the circuit.

c. If the resistance of the circuit is 2 ohm, find the value of X and XC at resonance.

d. Find the value of Land C at resonance.

Reference no: EM13249309

Questions Cloud

What is the output rate for the line : An assembly line with 17 tasks is to be balanced. The longest task is 2.4 minutes, and the total time for all tasks is 18 minutes. The line will operate 450 minutes per day.
Determine the maximum velocity attained by the mass : A mass is attached to a spring. It oscillates at a frequency of 4/? Hz when displaced a distance of 7.00 cm from equilibrium
Explain the partial pressure of helium is the same as oxygen : If the partial pressure of helium is the same as the partial pressure of oxygen, what do you know about the number of helium atoms compared to the number of oxygen molecules? explain.
Evaluate the implementation of customer service : How would you evaluate the implementation of customer service in each store? Compare them based on criteria that you develop.
Find the value of land c at resonance : The cutoff frequencies of a series resonant circuit are 5400 Hz and 6000 Hz. a. Find the bandwidth of the circuit. b. If Qs is 9.5, find the resonant frequency of the circuit.
Evaluate the implementation of customer service : Suppose you are a personnel manager, and an individual with long hair and no necktie applies for a job as an engineer. Imagine your reaction.
Find the magnitude and direction of particle momentum : A 3.07 kg particle has a velocity of (3.10 i hat - 4.04 j hat) m/s. Find the magnitude and direction of its momentum
Explain what is the partial pressure of the co2 gas : The vapor pressure of the water at 16 degrees C is 14 mmHg; CaCO3(s)-->CaO(s)+CO2(g): a) what is the partial pressure of the CO2 gas? b) How many moles of CO2 gas were in the CO2 gas sample
Find the self-inductance of this solenoid : A technician wraps wire around a tube of length 33 cm having a diameter of 7.9 cm, Find the self-inductance of this solenoid

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Twenty voice signals are to be multiplexed and transmitted

Twenty voice signals are to be multiplexed and transmitted over twisted pair. What is the bandwidth required (in bps) if synchronous time division multiplexing is used

  Determine the minimum bandwidth and baud rate

Determine the minimum bandwidth, baud, and bandwidth efficiency for the following bit rates and modulation schemes - 8-QAM and 16-QAM. Fb = 2400 bps Fb = 4800 bps Fb = 9600 bps

  What is the time function of the incident electric field

A 9 GHz parallel polarized wave with an amplitude of 20 V/m is obliquely incident from air (z 0). Theta_i equals a 60-degree angle of incidence.

  How to convert numbers to 4-bit values

Convert both numbers to 4-bit values, take the 2's complement of 9 and add them. What happens to the carry out How does that compare with what happens when you subtract 8 from 9

  Create a bandpass filter with cutoff frequencies

Create a bandpass filter with cutoff frequencies of 100-1k, attenuate by at least 3db at desired frequency(100-1k) and at 60Hz attenuate by 10 db. Resistor, Capacitor, Inductor, and Op-amps can be used.

  Explain in you own words how a modem works

Describe in you own words how a modem works and what steps the data goes through to be sent from one terminal to another via modem.

  Design a simple pnp current source for output current

(a) Design a simple PNP current source to give an output current of IO = 0.5 mA (nominal value). The transistor parameters are f = 50, VEE = 10 V, VCC = 10V, |VBE| = 0.7 V, |VCEsat| = 0.3 V and VA = 50 V (for all transistors)

  What is the sensitivity of the sensor system

The potentiometer is designed to rotate 330 degrees to give the full range of possible resistance. However, the actual measurement range that is used is only 165 degrees indicating positions of a liquid sensor float ranging from 0 to 10 cm (empty ..

  Calculate value of resistance that should be added to rotor

A 15 hp, 209V,three-phase,six pole, Y-connected induction motor has the following parameter values per phase: R1= 0.128 ohm, R'2=0.0935 ohm Xeq- X1 + X'2 = 0.49 ohm. The motor slip at full load is 3%, and the efficiency id 90%.

  What are the different methods used in frequency response

what are the different methods used in frequency response analysis

  Find vt of the nmosfet when n+ poly-si is used

An nMOSFET and pMOSFET are fabricated with substrate doping concentration of 6x1017/cm3. The gate oxide thickness is 5 nm. (a) Find Vt of the nMOSFET when n+ poly-Si is used to fabricate the gate electrode.

  Find the net heat transfer for the process in kj

50 kg of a certain gas is contained within a piston-cylinder assembly. the gas undergoes a processwhich the pressure volume relationship is PV = constant. (n=1.5) the given conditions as follows : p1= 6 bars, v1=0.2 cubic meters ,and v2= 0.4 cubic..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd