Find the value of heat transfer coefficient that will

Assignment Help Mechanical Engineering
Reference no: EM13639023

A 2.5 cm thick layer of insulation (k= 1.5 W/m oC) is applied to a plane surface so that the inner surface of the insulation is maintained at 150oC. The insulation outer surface is exposed to ambient air at 35oC to which it loses heat by convection. Find the value of heat transfer coefficient that will ensure that the surface temperature will not exceed 45oC. What is the heat flux through the insulation?

Reference no: EM13639023

Questions Cloud

Ball a is dropped from the top of a building of height h at : ball a is dropped from the top of a building of height h at the same instant that ball b is thrown vertically upward
Calculate the emf of a cell operating with the : calculate the emf of a cell operating with the followingreaction at 25oc in which mno4- 0.010 m br- 0.010 m mn2 0.15
It is known that atmospheric air flows parallel to the flat : as a heat transfer specialist for a large company in the mid-west you have been asked to determine the power needed to
If the friction force on the metal foil surface is 03 n : air at 1 atm and 20 deg c is flowing over the top surface of a 0.2 m x 0.5 m-long metal foil. the air stream velocity
Find the value of heat transfer coefficient that will : a 2.5 cm thick layer of insulation k 1.5 wm oc is applied to a plane surface so that the inner surface of the
Estimate the heat flux through the wall for following : a composite wall consists of a 13mm thick inner plaster board a 192 mm thick fiberglass blanket insulation and a 20 mm
The height of the cliff is 669 m the stones are thrown with : two stones are thrown simultaneously one straight upward from the base of a cliff and the other straight downward from
If 2958ml of 0550m naoh isrequired to titrate the oxalic : you have a mixture of oxalic acidh2c2o4 and another solid thatdoes not react with sodium hydroxide. if 29.58ml of
Calculate the time the boy must wait until the surface : a boy places his glass marbles in an oven at 200degreec. the diameter of the marbles is 15 mm. after a while he takes

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Set up the negative feedback system

Using MATLAB Simulink, set up the negative feedback system of and find the value of the gain

  A piston-cylinder device contains liquid and vapor water in

a piston-cylinder device contains liquid and vapor water in equilibrium at a pressure of 14.7 psia. the mass of the

  A full revolution press has 100 rpm flywheel rotation the

a full revolution press has 100 rpm flywheel rotation. the press is equipped with tow hand trip devices mounted on the

  The wedge velocity follos the relations vx 151-100t-012

a wedge cam has a cycloidal profile. the follower must rise 0.05m as the cam advances through 0.2m in time t0.2s.the

  Knowing that timber of 4-in nominal width 935-in actual

a 12-ft-long overhaning timber beam ac with an 8-ft span ab is to be designed to support the distributed and

  Pressure ratio 92 air at compressor inlet is at 25 deg f

consider a brayton cycle with the following given data pressure ratio 9.2 air at compressor inlet is at 25 deg f air

  The pipe are filled with ethyl alcohol to a level of 15 m

a cylindrical tank with its axis horizontal has a diameter of 2.0 m and a length of 4.0 m. the ends if the tank are

  A go-kart including driver weighs 800 lbs during an

1. a go-kart including driver weighs 800 lbs. during an aggressive braking event the vehicle decelerates from 60

  A closed system contains 2kg of air undergoes an isothermal

1 a piston-cylinder device contains air initially at 150kpa 20oc and 0.5m3. the air is now compressed in a polytropic

  Knowing the mass center of the automobile and driver is 2

a stunt driver proposes to drive a small automobile at the speed of 45 mihr on the vertical wall of a circular pit of

  A analyze the heat exhange between the hot resevoir and

a steam turbine power plant is based on the ideal rankine cycle the working fluid is water. the heat transfer from the

  If the tube elongates 3mm and its circumfrence decreases

a thin-walled tube is subjected to an axial force of 40 kn. if the tube elongates 3mm and its circumfrence decreases

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd