Find the total loss through the guide and the phase delay

Assignment Help Electrical Engineering
Reference no: EM13230574

A 10 cm length of a K-band copper waveguide is filled with a dielectric material with er = 2.55 and tan f = 0.0015. If the operating frequency is 15 GHz, find the total loss through the guide and the phase delay from the input to the output of the guide.

Reference no: EM13230574

Questions Cloud

Compute the ph at the equivalence point for titrating : Calculate the ph at the equivalence point for titrating 0.170 solutions of each of the following bases with 0.170 M HBr.
Discribe reproductive isolation and genetic mutation : Explain the difference between allopatricand sympatric speciation gene flow, reproductive isolation, genetic mutation, allele frequencies, and subpopulation. Finally, give a detailed example of how each type of speciation might occur.
Descrribe what is the empirical formula : A carbon-hydrogen-oxygen containing compound yields 1.029 g CO2 and 0.198 g H2O in a combustion analysis( note that this means O2 was added the overall reaction) what is the empirical formula? if the Molar mass is 138.16 what is the molecular form..
How is the principle of inclusion and exclusion related : How is the principle of inclusion and exclusion related to the rules for manipulation and simplification of logic predicates you learned in Ch. 2
Find the total loss through the guide and the phase delay : A 10 cm length of a K-band copper waveguide is filled with a dielectric material with er = 2.55 and tan f = 0.0015. If the operating frequency is 15 GHz, find the total loss through the guide and the phase delay from the input to the output of th..
Explain direct reaction of sodium metal with o2g leads : Direct reaction of sodium metal with O2(g) leads to sodium peroxide, Na2O2, which contains a peroxide complex anion and is diamagnetic. Direct reaction of potassium metal with O2(g) leads to potassium superoxide, KO2, which contains a superoxide c..
What is the resolution of an 8-bit dac : Which of the following is not an advantage of SPI transmission over SCI transmission Error checking via parity bit Faster transmission Master-slave capability Synchronous transmission A HCS12 embedded timer is in PWM mode.
Define the constitutional law theory : Define the constitutional law theory that would help Joan and Don to defeat the law and its application to their business.
Determine the minimum and maximum cycle times : An assembly line with 11 tasks is to be balanced. The longest task is 2.7 minutes, the shortest task is 0.4 minutes, and the sum of the task times is 18 minutes. The line will operate for 800 minutes per day.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine the change in the regulated output voltage

A shunt regulator utilizing a zener diode is biased on through a 100 resistor. Determine the change in the regulated output voltage for the two situations below: a) VI changes +2.0 V, ILoad constant b) ILoad changes +100 mA, VI constan..

  Determine the rms input and output noise levels

Assume that a receiver has a first amplifier stage with a 5KW input resistance, a gain of 300, an input audio signal of 20 mV, and an operating temperature of 27oC. When the amplifier is operating with a bandwidth first of 10 MHz,

  Determine the transfer function of the rlc circuit

Determine what kind of filter (low pass, high pass, bandpass, or band stop) the circuit represents. Briefly justify your answer. Confirm by computing the Bode plot using MATLAB and paste the graph below.

  What is the current through the resistor

A 1.0 dc voltage source is connected across a 10 ohm resistor. What is the current through the resistor if (a) the voltage source is ideal (b) the voltage source has internal resistance 0.1 ohm (c) internal resistance 1.0 ohm

  Draw the complete circuit including the load

Design a DC power supply that provides -95v +/- 5v to a 2 amp load (energy absorber). The input source is a 100 volt peak sinusoid, 60 Hz. You may use any circuit element we've studied. State the values of all circuit elements

  Define asic design

"Divide by 3 clock with 50% duty cycle" is the most commonly asked ASIC design question. This solution gives a simple design in which only 1 counter is required which works only on positive edge of the clock.

  Derive a suitable sequential circuit

A sequential circuit has two inputs w 1 and w 2 , and an output, z. Derive a suitable circuit for the given condition.

  What is the distance between the slits

Two slits produce fringes on a screen that is at a distance of 2.05 m from the slits. When the wavelength is 608 nm, the fringTwo slits produce fringes on a screen that is at a distance of 2.05 m from the slits. When the wavelength is 608 nm, the f..

  What is maximum possible power that could have been generate

The One river Hydroelectric Project generated power for BPA along the Two River from the early 1800s until 1900, when it was decommissioned due to environmental issues. The maximum flow rate through the system was 25 m3/s, and the hydraulic head w..

  Determine what is the value of the resistor

for a series RLC circuit shown, the input-output differential equation of interest is LC d^2 vl(t) /dt^2 + C dv l(t)/dt + vl(t) = LC d^2v(t)/dt^2 What is the Value of the Resistor

  Draw block diagram of a communication channel

Explain the characteristics of electromagnetic waves and application to communications systems and determine the signal spectra for the content of complex waveforms

  Calculate the mmf when the machine operates

calculate the mmf when the machine operates at rated voltage at full load? PLease explain how to get the solution to this problem?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd