User Account

All Pages

Find the thevenin and norton circuits for the sensor

Assignment Help Electrical Engineering
Reference no: EM13246855

an unknown sensor is investigated by connecting resistors across the output and measuring the current through them. When a resistance of 30? is connected the current through it is 0.5A. When the resistance is replaced by 20?, the current through it becomes 0.55A. Find and draw the Thevenin and Norton circuits for this sensor.

Reference no: EM13246855

Questions Cloud

Explain what is the role of ferric chloride : Why is acceptable to use a mixture of the alpha and beta anomers of D-(+)-mannose in this reaction? (i.e. why isn't it necessary to use either a pure alpha or the pure beta anomer
Design a low-pass filter that attenuates the noise : A measurement signal has a frequency less than 1 kHz, but there is unwanted noise at about 1 MHz. Design a low-pass filter that attenuates the noise to 1%. What is the effect on the measurement signal at its maximum of 1 kHz
Determine the acceleration of the rocks : Some sliding rocks approach the base of a hill with a speed of 15.0m/s . The hill rises at 42.0? above the horizontal, Find the acceleration of the rocks as they slide up the hill
Define the concentration of the filtered solution : After mixing, you filter it and find that the concentration of the filtered solution is 5ppm Cu2+. From the above scenario, calculate the mass of Cu2+ bound to the soil. Calculate the K(dis).
Find the thevenin and norton circuits for the sensor : an unknown sensor is investigated by connecting resistors across the output and measuring the current through them. When a resistance of 30 is connected the current through it is 0.5A. When the resistance is replaced by 20
Explain the concentration of nitrate ions left in solution : 10.0 mL of a 0.30 M sodium phosphate solution reacts with 20.0 mL of a 0.20 M lead(II) nitrate solution (assume no volume change). What is the concentration of nitrate ions left in solution after the reaction is complete
How much ice can it make in one hour : An ice machine converts 10 degree celsius water to 0 degree celsius ice. The ice machine has a COP of 3 and consumes elec
How much energy is transferred to the gas as heat : The temperature of 3.00 mol of an ideal diatomic gas is increased by 40 degrees C without a change in pressure, How much energy is transferred to the gas as heat
Determine the intensity for a sound : What is the intensity level in decibels for a sound with an intensity of 2.35×10-4 W/m2, What is the intensity for a sound with an intensity level of 79.9 dB

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine the source voltage of power transmission system

Determine the source voltage Vs of a 60-Hz power transmission system from the loading conditions described as follows: 1. The load is capacitive and absorbs 12 kW at 240

  What is the highest power supply in v

Assume you buy a 1 kOhm resistor with +/- 20% tolerance in its value. You would like this resistor to consume at most 2 W of power, otherwise it might burn. What is the highest power supply in V you would use to power it

  What is the magnitude of the instantaneous current

A charged 100-pf capacitor has initial voltage across it of 10V. a 100kohm resistor is suddenly connected across the capacitor (at t=0) to discharge it. What is the magnitude of the instantaneous current at 20 usec?

  What would be the general form of a voltaqe v

Given a circuit with 10 resistors, a CCVS gix, two independent voltage sources v1 and v2, as well as an independent current source i1. What would be the general form of a voltaqe v across a specific resistor R

  Determine the magnitude of the line current from the source

Two balanced Y-connected loads in parallel, one drawing 15 kW at 0.6 power factor lagging and the other drawing 10 kVA at 0.8 power factor leading, are supplied by a balanced, three-phase, 480-volt source.

  Determine the appropriate operating frequency and voltage

A three-phase induction motor has been tested, and has small stator resistance. At 230 V, 60 Hz, the motor produces 40 N-m at 1740 RPM.a) Given a 40 N-m load, input of 115 V and 30 Hz, what operating speed do you expect

  Design a voltage-divider network to supply the load

The voltage across the load must remain between 4.7 and 5.0 V for all values of load current. Design a voltage-divider network to supply the load. You may assume that resistors of any value desired are available.

  Generating multivariate random variables

Generate a new random variable X with pdf fX. Specifically, we want to generate a Gaussian random variable and relationship between Rayleigh and Gaussian distributions.

  In which characters move around cross obstacles

an inventory control system that keeps track of what items are in stock when the level falls below a certain value ?

  Define the angle of departure is defined

The angle of departure is defined as 180 degrees plus the phase angle of GH computed at the complex pole, but ignoring the contribution of that particular pole.

  How much power is dissipated at the load

A 75  lossless line is terminated in error with a 93 resistor. A generator sends 100 mW down the line. (a) What is the SWR on the line (b) What is the reflection coefficient

  Design by direct implementation the electronic circuits

Design by direct implementation the electronic circuits for equations as the following logic equations using any real 1, 2, or 3 input logic gates. Assume all signals are high true (positive logic) and do not simplify the equations.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd