User Account

All Pages

Find the stress and the strain in all three dimensions when

Assignment Help Mechanical Engineering
Reference no: EM13626988

A strip of material 1 inch wide, w, and initially 1/16 in. thick is compressed between flat dies to one half its original height. The die depth, b, is 1/4 inch. Model the material by s = 17+18*epsilon (ksi). Find the stress and the strain in all three dimensions when compressed. Then, find the force on the die, according to the maximum shear stress criterion and according to the distortion energy criterion. Finally, explain the difference between these two results. What was this material?

Reference no: EM13626988

Questions Cloud

A random dot stereogram is defined in wikipedia as a pair : a random dot stereogram is defined in wikipedia as a pair of images of random dots which when viewed with the aid of a
An ideal diesel cycle with air as the working fluid has a : an ideal diesel cycle with air as the working fluid has a compression ratio of 20 and a cutoff ratio of 1.3. this cylce
The critical heat flux of water at 1 atm is qmax 12587 kwm : the critical heat flux of water at 1 atm is qmax 1258.7 kwm which occurs at ?t 30c. boiling enters the transition
After inhaling most humans will float in fresh water albeit : after inhaling most humans will float in fresh water albeit with only a small fraction of their body above water. after
Find the stress and the strain in all three dimensions when : a strip of material 1 inch wide w and initially 116 in. thick is compressed between flat dies to one half its original
The metlife blimp snoopy one is moving at a constant : the metlife blimp snoopy one is moving at a constant velocity of 18.93 ms. its velocity vector makes an angle of 15
Basically a block is slid down from left side of the circle : basically a block is slid down from left side of the circle and when it reaches the middle of the bottom the speed of
For the ideal air standard diesel cycle with a volumetric : for the ideal air standard diesel cycle with a volumetric compression ratio of 17 1 calculate the efficiencies for
Given that the energy difference between the first 2 energy : calculate the total number of state between the first energy level and the second energy level for a quantum well of

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The main purpose of this heat exchanger is to prevent

a walk-in cooler using a vapor compression refrigeration cycle is configured as shown below. the cycle uses cfc22 or

  The field-circuit resistance and armature-circuit

the field-circuit resistance and armature-circuit resistance of a 10-hp 115-v motor are 90 ohms and 0.08 ohms

  Find the complete initial and final states t p v h u and

find the complete initial and final states t p v h u and sdeg for the following ideal gas process air at 260 f and 15

  Estimate the blood pressure in each branch

Estimate the blood pressure in each branch, assuming that blood vessels behave as rigid tubes, that we have frictionless flow, and that the vessel lies in the horizontal plane. What is the force generated at the branch by the blood? You may approx..

  Water pressure of 10 kpa is pumped to a pressure of 4mpa

water pressure of 10 kpa is pumped to a pressure of 4mpa. what is minimum energy requirement of the pump in kjkg.

  Determine the number of vehicles needed to satisfy

determine the number of vehicles needed to satisfy the indicated deliveries per hour? Assume that availability = 0.90.

  Two kilograms of refrigerant134a initially at 2 bar and

two kilograms of refrigerant134a initially at 2 bar and occupying a volume of 0.12 m3 undergoes a process at constant

  A 1875 inch diameter shaft machined from aisi 1018 cd

a 1.875 inch diameter shaft machined from aisi 1018 cd steel supports a bending load during operation at 1750 rpm. if

  Detemine the normal and shearing stresses

Knowing that the pipe has inner and outer dimensions equal to 35 and 42 mm, respectively, detemine the normal and shearing stresses at point a and point b.

  The prizes are all the same so the order in which the

at a certain event 16 people attend and 5 will be chosen at random to receive door prizes. the prizes are all the

  Compute the force required to punch out a rectangular

Calculate the force required to punch out a rectangular hole 100m x 50mm in a 2mm thick aluminium sheet. The ultimate strength in shear is 125 MN/m^2.

  Bubble dynamics underneath a downward facing anode in

bubble dynamics underneath a downward facing anode in hall-heroult cell.1.introductionthe basic characteristics of the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd