Find the steady-state concentration if the air is assumed to

Assignment Help Civil Engineering
Reference no: EM13544577

Consider the air over a city to be a box 100 km on a side that reaches up to an altitude of 1.0 km. Clean air is blowing into the box along one of its sides with a speed of 4 m/s. Suppose an air pollutant with rate constant k= 0.20/hr is emitted into the box at a total rate of 10.0 kg/s. Find the steady-state concentration if the air is assumed to be completely mixed.

Reference no: EM13544577

Questions Cloud

How to get the intensity of the rainfall from information : For a hydrology question we are given the depth of runoff and the time. We are to make a hyetograph using this information but Im not sure how to get the intensity of the rainfall from this information
What would the concentration in the effluent be 7 days later : A lagoon with volume 1200 m3 has been receiving a steady flow of a conservative waste at a rate of 100 m3/day for a long enough time to assume that steady-state conditions apply. The waste entering the lagoon has a concentration of 10 mg/L. Assuming ..
What is the minimum possible value for this pressure : Part of a vertical piping system consists of 8 ft of 4 in diameter, connected to 8 ft of 3 in diameter above, and connected to 8 ft of 2 in diameter above that. Water at 60 F flows up the pipe (no downward flow occurs)
What pressure must be provided at point 1 if you neglect : A pressure gage at elevation 4.8 m on the side of a storage tank containing oil reads 34.7 kPa.Another gage at elevation 2.2 m reads 57.5 kPa. Compute the specific weight, density, and specific gravity of the oil.
Find the steady-state concentration if the air is assumed to : Consider the air over a city to be a box 100 km on a side that reaches up to an altitude of 1.0 km. Clean air is blowing into the box along one of its sides with a speed of 4 m/s.
Suppose the utility encourages its customers to replace : Suppose a utility generates electricity with a 36 percent efficient coal-fired power plant emitting the legal limit of 0.6 lb of SO2 per million Btus of heat into the plant. Suppose the utility encourages its customers to replace their
What is the speed of the train relative to : The train is travelling at 0.8 m/s i relative to a man on the side of the tracks. What is the speed of the bug as seen by the man at the side of the tracks? What is the speed of the train relative to (or as seen by) the bug?
Determine the batch weights needed for all materials for : Determine the batch weights needed for all materials for a 1yd^3 batch yielding an f'c= 2500 psi given the following information.
What is the largest number of phases that can coexist at : Considering both temperature and pressure to be variables, what is the largest number of phases that can coexist at equilibrium in a binary alloy?

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine what is the decrease in diameter d

A bar of monel metal (length L=9 in., diameter d=0.225 in.) is loaded axially by a tensile force P. If the bar elongates by 0.0195 in., what is the decrease in diameter d What is the magnitude of the load P

  The horizontal distance between the point

The elevtion of M is 875 . a transit was set at point M and a leveling rod was held vertically at point N. the horizontal cross line of the telescope was inclined so the reading of the horizontal cross line

  Determine allowable stress design reference and values

determine the Allowable Stress Design (ASD) reference and adjusted design values for the following members and loading conditions. All members are No. 2 Hem-Fir and are fully braced to prevent lateral-torsional buckling.

  Verify that the hazen williams equation

Verify that the Hazen Williams equation

  Determine what will the discharge be in each branch

A 48-in water main carries 79 cfs and branches into two pipes at point A. The branching pipes are 36 and 20 in. in diameter and 2800 and 5000 ft long, respectively. These pipes rejoin at point B and again form a single 48-in.

  Determine from curve the maximum flow rate

Determine from curve (a) critical depth (b) the maximum flow rate (c) the flow rate at a depth of 2.4 m and (d) the depths at which flow rate of 28.3 m^3/s may exist and the flow conditions at these depths.

  What is the current draw of the motor during the operation

The motor has an efficiency of 80%. It operates at 240V AC. A 12" diameter drum is attached to the gearbox output shaft, and a wire rope is wrapped around the drum to act as a winch. The winch is used to raise bucket of raw material in a factory.

  Calculate the angles made by f with the positive x and y

A force is specified by the vector F = [(10)i + (150)j + (-50)k] N. Calculate the angles made by F with the positive x-, y-, and z-axes

  Plot a mohr circle

Shear and normal stresses on aplane that is 37 degrees from horizontal

  Determine what is the drag coefficient at sea level

A 2,150 lb car is traveling at sea level at a constant speed. Its engine is running at 4500 rev/min and is producing 150 ft-lb of torque. It has a driveline efficiency of 90%, a driveline slippage of 2%, 15-inch radius wheels and an overall gear r..

  Calculate the work produced and heat rejected by the engine

A completely reversible heat engine uses a solar receiver for a hightemperature reservoir and a lake for a low temperature reservoir. The sun maintains the receiver surface at 290 ° F while the lake remains at 40 °F.

  An electric motor is rated at 10 horsepower hp and costs

an electric motor is rated at 10 horsepower hp and costs 800. its full load efficiency is specified to be 85. a newly

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd