Find the state of the escaping fluid

Assignment Help Mechanical Engineering
Reference no: EM13711606

A pipe system carries a steam-water mixture at 250 psi, 95% quality. A leak develops in the pipe allowing the fluid to escape to the building which is at atmospheric pressure. Treating the leak as a throttling process, find the state of the escaping fluid.

Reference no: EM13711606

Questions Cloud

Assume a linear concentration profile within the plate : A 5mm thick sheet of palladium with a cross sectional area of 0.2m^2 is used as a steady-state diffusion membrane in order to purify H2.The H2 concentration on the high pressure side of the sheet (i.e., the impure H2) is 1.5kg/m3 and that at the low ..
Throttling valve is used in an air conditioning system : A throttling valve is used in an air conditioning system to reduce the pressure of refrigerant: R134a as it flows from a condenser to an evaporator. The refrigerant enters the throttling valve at a pressure of 140psia and a temperature of 95F and lea..
What are the final pressure and temperature inside the tank : An adiabatic vessel contains steam at 180 [C] and 116 [kPa]. The volume is 0.5 [m^3]. Steam at 150 [C] with a quality of 0.85 is fed into the vessel until the flow stops. What are the final pressure and temperature inside the tank? What is its qualit..
Erythroblastosis fetalis (ef) is a condition : Erythroblastosis fetalis (EF) is a condition that causes the mother's red blood cells to attack those of the baby as if they were any foreign invaders. It is referred to as hemolytic anemia of the newborn. It is caused by anti-Rh antibodies fr..
Find the state of the escaping fluid : A pipe system carries a steam-water mixture at 250 psi, 95% quality. A leak develops in the pipe allowing the fluid to escape to the building which is at atmospheric pressure. Treating the leak as a throttling process, find the state of the escaping ..
Calculate mass needed to achieve mechanical noise limit : For mass-spring-damper accelerometer, calculate the mass needed to achieve mechanical noise limit a_rms = 1 nG if the mechanical resonance frequency is to be f=100 Hz.
Types of consequences of operant conditioning : Man's Best Friend: The Biology and Behavior of Dogs Describe a response that can be classified as classical conditioning (such as vet trips, grooming, thunder phobia, etc.) Describe four types of consequences of operant conditioning?
In air-conditioning systems-streams of cold and warm air : In air-conditioning systems, streams of cold and warm air are mixed to get air with the right temperature. Consider a mixing chamber into which cold air enters at 8C and 100 kPa at a rate of 0.55 m^3 /s and warm air enters at 300C and 100 kPa. The ra..
Range of projectile and velocity on impact given inputs : (MATLAB) given a cannon ball that is shot upwards at an angle, the time taken for the cannon ball to hit the ground is: Write a single function that outputs the total time of flight, range of projectile and velocity on impact given inputs. Use the fu..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What stresses are produced in the bolt and in the tube if

a 0.5-in.-diameter steel e 30000 ksi bolt 1 is placed in a copper tube 2 as shown in fig. p5.47. the copper e 16000

  Suppose you are marooned on an exotic island where the

suppose you are marooned on an exotic island where the natives happen to speak english. their ways are primitive

  Using the kelvin - planck statement of the second law of

using the kelvin - planck statement of the second law of thermodynamics demostrate the following corollariesa the

  The cloud being at the higher potential what is the change

during a particular thunderstorm the electric potential difference between a cloud and the ground is vcloud - vground

  A 150-lbm astronaut took his bathroom scale aspring scale

a 150-lbm astronaut took his bathroom scale aspring scale and a beam scale compares masses to themoon where the local

  Calculate the maximum shear stress for each stress element

A cantilever beam with a 1 in diameter is loaded at the tip with a transverse force of 1000 lb. Figure 2.1 below shows the beam configuration and cross-section with points A at the top, point B at the center and point C at the midpoint between A and ..

  Neglecting variations in the height of the vapour column in

1 a flat bottomed test tube of 200mm height and 10mm internal diameter stands on its base. it initially contains a

  Determine the minimum tensile strength each cable must have

due to a poorly designed foundation the statue at point a slowly slides down a grass covered slope. to prevent further

  Determine the largest mass m

the pin c will support a force of 24 knmagnitude.Based on this criterion, you are asked to determine the largest mass m that the frame can safely support.the diameter of pulley at d is given as 0.2 m.find maximum mass m that can be supported by fr..

  Determine the net work of the cycle in kj and the heat

a gas within a piston-cylinder assembly undergoes a thermodynamic cycle consisting of three processesprocess 1-2

  Calculate the sensible heat load due to the infiltating air

Outdoor air leaks into a building through cracks in the walls at the rate of 700 m3/h (this is infiltratation). The outside air is at a temperature of -16.1C and a humidity ratio of 0.001 kgv/kga. The density of the outside air is1.4 kg/m3. The indoo..

  Estimate the land area required to grow willow that would

estimate the land area required to grow willow that would provide 1 gw of power in a region where the annual solar

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd