Find the required mass flow rate of air through the turbine

Assignment Help Mechanical Engineering
Reference no: EM13701698

A small, high-speed turbine operating on compressed air produces a power output of 0.1 hp. The inlet state is 120 psi, 200°F, and the exit state is 14.7 psi, - 20 F. Assuming the velocities to be low and the process to be adiabatic, find the required mass flow rate of air through the turbine assuming a) constant specific heat and b) variable specific heat.

Reference no: EM13701698

Questions Cloud

Determine the thermodynamic efficiency and back work ratio : A regenerative gas turbine is planned to operate with inlet conditions of 100 kPa and 300 K, a pressure ratio of 6, a turbine inlet temperature of 1600 K, and a net power output of 150 kW. The effectiveness of the regenerator is 90% and the adiabatic..
Regenerator as well as reheating and intercooling : Air enters a THREE STAGE gas turbine at 100 kPa and 17 degree Celsius. This system uses a regenerator as well as reheating and intercooling.
What speed should the wind tunnel be run : A 1/10th scale model of an airplane is to be tested in a wind tunnel that operates with air at a pressure of 20 atmospheres. The plane is expected to fly at a speed of 500 [km/hr]. What speed should the wind tunnel be run?
What is the density of the vapor : A 3 liter vessel contains 2kg of water, 0.05kmol of steam, and 15cm^3 of ice (of density 990 kg/m^3). If the vessel is heated until its entire contents have vaporied, what is the density of the vapor?
Find the required mass flow rate of air through the turbine : A small, high-speed turbine operating on compressed air produces a power output of 0.1 hp. The inlet state is 120 psi, 200°F, and the exit state is 14.7 psi, - 20 F. Assuming the velocities to be low and the process to be adiabatic, find the required..
What is the mass of argon inside : A rigid sealed 50 liter tank contains Argo at a pressure of 5 MPa and 400K. What is the mass of argon inside?
What role do value propositions perform in models : According to the Business Model Generation and/or Strategic Management Concepts and Cases literature, what is a business model?
Prepare forrest company limited master budget : Prepare Forrest Company Limited master budget for each quarter of 2015 and in total for the year by completing the schedules and statements. Selling and administrative budget. (Round off variable cost to 2 decimal places and fixed cost to the neare..
Vertical cylinder fitted with a frictionless piston contains : A vertical cylinder fitted with a frictionless piston contains argon at 100C. The piston has a mass of 5kg and a diameter of 100mm, and the ambient pressure outside the cylinder is 97kPa. If the cylinder volume is 2 liters, what is the mass of argon ..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The rocker of a crank-rocker linkage is to have a length

the rocker of a crank-rocker linkage is to have a length of 500mm and swing through a total angle of 45 degrees with a

  Two identical and cfr computers are placed in a redundant

two identical and cfr computers are placed in a redundant configuration. if the system reliability is to be 0.95 at

  The following table lists temperatures and specific volumes

the following table lists temperatures and specific volumes of ammonia vapor at two pressures p 50 psi

  If the increase in th or the decrease in tl is amp kelvin

a reversible carnot power cycle operates between reservoirs th and tl. to increase the thermal efficiency of the cycle

  Determine the velocity of the air at the duct inlet

Determine (a) the velocity of the air at the duct inlet and (b) the temperature of the air at the exit.

  Determine the magnitude and direction of the force exerted

water density 1000 kgm3 flowing in a horizontal 25 cm diameter pipe at 8 ms and 300 kpa gauge enters a 90 degree

  The water discharges to 01mpa if the flow is isothermal

a high-velocity water jet at 30 degrees celcious is proposed for use as a cutting device with possible applications in

  The steam exits at a temperature of t220 degrees find the

steam at t1600 degrees c p115 mpa enters a reversible and adiabatic turbine at a flow rate of 300 kgs. the steam exits

  Determine the maximum stress and the difference in tube

a tube 4cm inside and 6cm outside diameter is to be reinforced by shrinking on a tube of 8cm outside diameter. the

  What can the engineer conclude about the manufacturers

an engineer measures the diameter of 20 tubes selected at random from a large shipment. the sample yields a sample mean

  Consider a 1000-w iron whose base plate is made of

consider a 1000-w iron whose base plate is made of 0.5-cm-thick aluminium alloy 2024-t6 p2771 kgm3 and cp 875 jkg c.

  A well-insulated turbine operating at steady state develops

a well-insulated turbine operating at steady state develops 28.75 mw of power for a steam flow rate of 50 kgs. the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd