Find the rate that the trucks line up

Assignment Help Civil Engineering
Reference no: EM13533441

1.Calculate the Hazen-Williams Coefficient (C) of a1-M diameter pipe with water flowing at 0.2 M3/sec if it has a headloss of 0.0012M/M

2.A notched beam, machined from AISI 1020 steel is subjected toreversed bending. Determine the endurance limit Se.Assume the survival rate of 99.9 percent and Cs = 0.75and that the fatigue stress concentration factor is Kf =2.5.

3.A container ship carries 2000 units. It must be unloaded andre-loaded in a 48 hr turnaround. Two cranes are available. Find the rate that the trucks line up, load and pass under each crane.

Reference no: EM13533441

Questions Cloud

The corresponding increase in the diameter of the vessel : A spherical gas container having an outer diameter of 15 ftand a wall thickness of 0.90 in. is made of a steel for whichE =29*106 psi and v = 0.29. Knowingthat the gage
Determine the corresponding height of capillary rise in soil : The void ratio of a given soil A is twice that of another soil B,while the effective size of particles of soil A is one-third thatof soil B. The height of capillary rise of water in soil A on acertain day is found to be 400 mm. Determine the correspo..
Calculate the pressure at the clay-sand interface for two : Calculate the pressure at the clay-sand interface for two cases:1) clay on top of the sand and 2) clay on the bottom of thevertical sand column.
What is the maximum torque the tube can transmit if the : A thin tube of 1/8 in thickness has a mean diameter of 6 in. What is the maximum torque the tube can transmit if the allowable normalstress in compression is 10 ksi?
Find the rate that the trucks line up : A container ship carries 2000 units. It must be unloaded andre-loaded in a 48 hr turnaround. Two cranes are available. Find the rate that the trucks line up, load and pass under each crane.
Calculate the diameter of this pipe : Using the Hazen-Williams approach (seecoefficient table below), find the headloss of water flowingthrough 1,000-ft of 6-ft diameter concrete pipe at a flow rate (Q)of 80 ft3/sec
What is the oil flowrate in stb : Two wells had been drilled on 40-acre spacing. Well 1 is injectionand Well 2 is producing well. Downhole injection pressure is 8500psi, and bottomhole pressure in producing well is 2400 psi.
How many passengers per day are carried : A bus line 4 miles long runs through an area with 1/6 acre lots,3.5 people per household, average 1 car per household. People willwalk up to 1/6 mile to a bus stop, so stops are located 1/3 mileapart along the route. Say commuters will tolerate 20 mi..
What is the demand for time if left turns are provided : Given the following geometry of an intersection: Four lanes fornorth and southbound traffic; two lanes for east and west boundtraffic. The peak hour volume for

Reviews

Write a Review

Civil Engineering Questions & Answers

  Design a one way slab to support a uniform live load

Design a one way slab to support a uniform live load of 300 psf. The beam is simply supported with a span of 20 ft. Use a reinforcement ration ( Ps) of 0.008 Use f'c=3000 psi and fy=60000 psi.

  Determine what is the pace length and the length of ab

A student counted 92,90,92,91,93, and 91 paces in six trials of walking along a course of 200 ft known length on level ground. Then 85,86,86 and 84 paces were counted in walking four repititions of an unknown distance AB.

  What are the pressure and temperature in absolute units

A closed tank having a volume of 1.0 ft3 is filled with 0.15 lb of a gas. A pressure gage attached to the tank reads 12 psi when the gas temperature is 80 F. There is some question as to whether the gas in the tank is oxygen or helium.

  Calculate the flow rate imprted by the impeller

A six bladed rushton turbine 2.0m in diameter rotating at 25 rev/min in a tank 4m deep, water temperature= 10 degree celcius. For this flocculation system calculate the following: a) Reynolds number

  What is the maximum internal pressure in cylindrical vessel

The maximum hoop stress is (65000/2) psi and the maximum shear stress is 16000 psi. If the diameter of the tank is 7 inches,what is the minimum wall thickness.

  Determine the angle theta which the 6-lb

uniform rod makes with the vertical during the roll, and (b) the speed of the roller after it moves 4 ft., starting from rest. The roller rolls without slipping, and the rod hangs vertically (theta = 0) when the system is at rest.

  What was students associated perception per reaction time

An engineering student is driving on a level roadway and sees a construction sign 500 ft ahead in the middle of the roadway. the student strikes the sign at a speed of 25 mi/h.

  What is the station of the pt

a horizontal curve on a single-lane highway has its PC at station 124 + 10 and its PI at station 131 + 40. The curve has a superelvation of 0.06 ft/ft and is designed for 70 mi/h. What is the station of the PT?

  Determine the back emf when giving an output

A 440 -V shunt motor has armature resistance of 0.8 ohm and field resistance of 200 ohm . determine the back emf when giving an output of 7.64 KW at 85% efficiency

  Displacement response of the system

Verify that the displacement response of the system - single-degree-of-freedom model below is subject to the pulse loading

  Define soda ash and quicklime

Soda Ash and QuickLime, A lime-soda softening plant treats a flow of 150 MGD, and the water has 86mg/l Ca2+, 35 mg/L Mg2+, 299 mg/L HCO3- and 6mg/l CO2.

  Determine the maximum velocity that the skier will achieve

A person with a mass of 200kg wearing snow skis is gliding down a long slope at an angle of 20 degrees. Each ski is 200cm long and 5 cm wide. The pressure of the skis on the snow melts a thin layer of water so that a

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd