Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Consider the downlink of the IS-856 system.
1. Suppose there are two users on the cell edge. Users are scheduled on a TDMA basis, with equal time for each user. The received SINR of each user is 0 dB when it is transmitted to. Find the rate that each user gets. The total bandwidth is 1.25 MHz and you can assume an AWGN channel and the use of capacity-achieving codes.
2. Now suppose there is an extra user which is near the base-station with a 20 dB SINR advantage over the other two users. Consider two ways to accommodate this user:
• Give a fraction of the time slots to this user and divide the rest equally among the two cell edge users.
• Give a fraction of the power to this user and superimpose its signal on top of the signals of both users. The two cell edge users are still scheduled on a TDMA basis with equal time, and the strong user uses a SIC decoder to extract its signal after decoding the other users' signals at each time slot.
Since the two cell edge users have weak reception, it is important to maintain the best possible quality of service to them. So suppose the constraint is that we want each of them to have 95% of the rates they were getting before this strong user joined. Compare the performance that the strong user gets in the two schemes above.
In designing a low-pass filter for an audio system, the filter stop band attenuation must be at least 40 dB at a frequency that is 2 times the passband frequency. The attenuation in the passband must be less than 1 dB.
The specification of the desired low pass filter are A min=23 dB, A max=5dB, P=02 and S=0.6. Design a Butterworth digital filter using bilinear transformation.
Write a program to count the number of even elements of an array of N 16-bit elements. The array is stored at memory locations starting from $900. Use assembler
Two ideal p-n junction diodes are connected in series across a 1 V battery such that both of them are forward biased (draw this). One diode has I0 = 10-5 A and another I0 = 10-8 A.
the ends of a length of wire are labeleda and b. If the current in the wire is iab = -3A, are electrons moving toward a or b? How much charge passes through a cross section of the wire in 3 seconds?
Explain with examples what linear time-invariant (LTI) system is. Consider the fourth order optimal FIR filter
What is the impedance of a resistor R in parallel with a series combination of a capacitor C and an inductor L? Assume angular frequency omega(w).
The transfer function of a second order system is given: T(s) = 1.05x10^7/(s^2 + (1.6x10^3)s + 1.05x10^7) a Find the values of f, fn, Ts, Tp, Tr, and % Overshoot.
design a propotional controller for a system with the transfer function G(z)=K/(z-0.4) to have a damping ratio of 0.7
Design an amplifier to sense open-circuit output voltage from a transducer and provide proportional current through a load resistor. The series resistance of the transducer is a range between 1 kOhms and 10 kOhms.
What is the Difference between Unilateral and Bi-Lateral Circuits & Elements ?
Assume all your standard value resistors are accurate to 0.1%. What would be the worst-case variation in overall resistance for your design (both high and low). How might you construct a resistive network using the smallest number of standard resis..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd