Find the rate of entropy generation in the cooling section

Assignment Help Mechanical Engineering
Reference no: EM13708482

Moist air at 45?C and relative humidity 30% (State 1) with another stream of moist air at 20?C and relative humidity 50% (State 2) in an adiabatic duct. Mass flow rate of dry air is 0.8 kg/s at section 1 and 1 kg/s at section 2. The mixed stream (State 3) is cooled until condensation is about to begin (State 4) at the exit. Temperature of the cooling section boundary is maintained at 5?C. Total pressure is 1 atm throughout the system.

a) Show the process for moist air on psychrometric chart. Label states 1 through 4.

b) Calculate temperatures (?C) of the mixed stream at sections 3 and 4 and relative humidity (%) at section 3.

c) Determine the rate of heat transfer (kW) in the cooling section.

d) Find the rate of entropy generation (kW/K) in the cooling section.

Reference no: EM13708482

Questions Cloud

Estimate the potential difference across the capacitor : A 3.3-cm-diameter parallel-plate capacitor has a 2.5mm spacing. The electric field strength inside the capacitor is 1.1×105V/m. What is the potential difference across the capacitor
Calculate volume in each cylinder when piston reaches tdc : A four-stroke engine has a total displacement volume of 10L, 125mm bore and 16.3:1 compression ratio. The engine produces a maximum of 210 kW at 2100 RPM. The intake air is at 45 degrees C and 22.5 g/s of air flow into each cylinder. Calculate the vo..
Estimate what is the minimum rope tension required : A heavy sled is being pulled by two people as shown in the figure. The coefficient of static friction between the sled and the ground is µs = 0.627, what is the minimum rope tension required
How far away from the object does the image form : An object is placed 1.7 meters in front of a plane mirror, forming an image. How far away from the object does the image form
Find the rate of entropy generation in the cooling section : Moist air at 45?C and relative humidity 30% (State 1) with another stream of moist air at 20?C and relative humidity 50% (State 2) in an adiabatic duct. Mass flow rate of dry air is 0.8 kg/s at section 1 and 1 kg/s at section 2. The mixed stream (Sta..
Find at what angle to the vertical is the ray transmitted : A light ray in air is incident on a piece of crown glass (n=1.5) at an angle of 37 degrees from the vertical. At what angle to the vertical is the ray transmitted into the glass
What is the kangaroo average acceleration : A Kangaroo is moving with a velocity of 5.0m/s at an angel of 30 degrees North of East. What is the kangaroo's average acceleration
How long will it take to reach the bottom of hill : A bobsledder starting from rest accelerates uniformly down a 30 degree hill at 3.30m/s2. How long will it take to reach the bottom of the hill if her change in elevation is 110m
Non-reacting gaseous mixture with molar analysis : A non-reacting gaseous mixture with molar analysis of 74.3% N2, 4.3% O2, 7.1% CO2, and 14.3% H2O (g) enters a counter-flow heat exchanger at 800?F and 1 atm with a volumetric flow rate of 5 ft3/s (State 1) and exits at 200?F (State 2). A separate moi..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the specific volume of superheated water vapor at

determine the specific volume of superheated water vapor at 15mpa and 350oc using a the ideal gas equation b the

  Calculate the pipe diameter

Calculate the pipe diameter D in inches to 2 decimal places required to give the fluid velocity of 4 ft/sec in the following situation: The formula for the velocity is given by: velocity =Flow rate / Pipe Area And the flow rate = 21 gpm and the Pipe ..

  Using the same power found in the part a above what would

a heat pump will be used to heat a building during the winter and will then cool the same space during the summer. the

  A metal is being cast into a cylinder

A metal is being cast into a cylinder which is 10 cm in diameter and 20 cm tall. The mold is bottom-gated (see class notes for geometry)

  What is the density of air leaving the compressor what is

a compressor takes in air at 100 kpa and 300 k and discharges it at 0.25 kgs at 1.2 mpa and 450 k. unfortunately the

  An electron is shot vertically straight up from the ground

in a particular location the horizontal component of the earths magnetic field has a magnitude of 2.00 10-5 t. an

  Find the change of entropy using the ideas gas table and

air undergoes a process with the states given below. find the change of entropy using the ideas gas table and compare

  Determine the following parameters a the pressure and

design a turbojet engine to flight at an altitude of 10000m. the pressure ratio across the compressor is 3. the

  Constant-temperature compression to volumetric

A sealed piston-cylinder assembly contains 3 lbm of water. The water is initially at P1 = 40 psia and T1 = 300°F. The water undergoes two processes in series: Constant-temperature compression to Volumetric = 11.19 ft3, during which the water transfe..

  A system contains refrigerant r-134a with the specific

1. a system contains water at 4.0 mpa and 275 degc. the phase of water isa liquid onlyb liquid-vapor mixturec vapor

  A car travels along a circular path of radius 500 m the

a car travels along a circular path of radius 500 m. the speed of the car can be expressed as v 0.0002 s2 ms where s

  Compression processes in piston-cylinder devices

During some actual expansion and compression processes in piston-cylinder devices, the gases have been observed to satisfy the relationship PVn= C, where n and C are constants. Calculate the work done when a gas expands from 350 kPa and 0.03 m3 to a ..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd