Find the probability that the defective board was produced

Assignment Help Electrical Engineering
Reference no: EM131196587

The number of defective circuit boards among those coming out of a soldering machine follows a possion distribution. On a particular 8-hour workday, one defective board is found.

a Find the probability that it was produced during the first hour of operation of that day.

b Find the probability that it was produced during the last hour of operation for that day.

c Given that no defective boards were seen during the first 4 hours of operation, find the probability that the defective board was produced during the fifth hour.

Reference no: EM131196587

Questions Cloud

Detailed explanation of filters in chemical instrumentation : Provide a detailed explanation of filters in chemical instrumentation and also describe detectors and a general subscription of the whole system.
Find the probability that the target is destroyed : The target will be destroyed if the bomb falls within a tenth of a mile on either side of the center. Find the probability that the target is destroyed if the bomb falls randomly along the line.
How does the concept of wisdom in nursing informatics : Describe a nursing-practice situation in which you applied or otherwise experienced the transformations of data to information to knowledge, finally to application of wisdom (DIKW).
How to make subway train fast and cheap : How to make subway train fast and cheap; and to use less energy? - What type of energy is effective for subway train?
Find the probability that the defective board was produced : The number of defective circuit boards among those coming out of a soldering machine follows a possion distribution. On a particular 8-hour workday, one defective board is found.
Find the mean and variance of these measurement errors : Find the probability that a particular arrival time measurement will be in error by less than 0.01 microsecond.
How important is fairness with respect to work motivation : How important is fairness with respect to work motivation? What are the strengths and the drawbacks of the equity perspective? Provide examples of each.
What is the total charge in the inner wall of shell b : What is the total charge in the inner wall of shell B?- What is the total charge on the outer wall of shell B?- What is the total charge in the inner wall of shell A?
Causes of world war i : Identify and explain at least two causes of World War I. Then analyze the events that drew the United States into World War I. Evaluate America's contribution to the war effort and to what extent America's entry contributed to the end of the war. ..

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Explain the design requirements under charge sharing

Explain charge sharing in dynamic circuits. For a 3-input dynamic NAND gate, discuss charge sharing, and explain the design requirements under which the gate operates correctly in the presence of charge sharing.

  Write a verilog hdl module for the state machine

Create a state transition diagram for a simple state machine to detect a positive pulse. You choose either a Moore or Mealy machine. Write a Verilog HDL module for your state machine.

  The carrier frequency

The output voltage of an AM transmitter is given by 500(1+.4sin3140t)sin6.28x107t. This voltage is fed to a load of 800 ohms. Determine the following. The carrier frequency The modulating frequency The peak carrier amplitude

  What is turns ratio of a step-down transformer

A 115/28 V transformer has 56 turns on its low voltage side. How many turns does it have on its high voltage side what is its turns ratio when it is used as a step-down transformer

  Determine the maximum tensile and compressive stresses

Two vertical forces are applied to a beam of the cross section shown. Determine the maximum tensile and compressive stresses in portion BC of the beam.

  Use the fourier series analysis integral to compute

Draw a labeled sketch of x(t) over a few periods: be careful, make sure you follow the exact definition of x(t)

  Which real wage rate is higher

In 1988, the average wage rate was $9.45 an hour and in 2008 the average wage rate was $18.00 an hour. The CPI in 1988 was 118.3 and in 2008 it was 215.3 . Which real wage rate is higher?

  Find the necessary lo phase noise specification

The final IF voice bandwidth is 12 kHz.

  Determine the maximum stress in the bar

A couple of moment M = 2 kN.m is to be applied to the end of a steel bar.

  What is corresponding change in the regulated output voltage

A shunt regulator utilizing a zener diode with an incremental resistance of 5ohm is fed through an 82ohm resistor. If the raw supply changes by 1.0V, what is the corresponding change in the regulated output voltage

  Calculate the per unit resistance of this transformer

Efficiency in a power transformer is 98.6 percent when loaded such that its copper losses are five times its core losses. Calculate the per unit resistance of this transformer.

  Fxyyinvxy dom fxyxxgt0 is f convex if not give a simple

fxyyinvxy dom fxyxxgt0. is f convex? if not give a simple counterexample.i can proof convexity when x is restricted to

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd